Parker SciLog FilterTec Plus Скачать руководство пользователя

Страница: 40 / 72

4.1 PROGRAMMABLE R-P: Setup

SUMMARY:

The Setup menu is identical to the Edit menus in the other two modes except that

the Pump Rate and Pump Pressure are input as part of the Step-by-Step instructions mentioned
in the previous section.

Use

“Up”

and

“Down”

keys to make a selection, then press

“Select”

to implement that

selection.

Pump Tubing:

Select sizes #13, 14, 16, 25, 17, 15, 24 or #35, use

“Up”

and

“Down”

keys for

choice of pump tubing size, then press

“Select”.

Based upon your selection

the FilterTec Plus

will access factory installed calibration tables, which relate the system output in ml/min. to motor
speed. The FilterTec Plus output can also be re-calibrated by the utilizing the front panel star
(



) key. (See CONSTANT RATE Mode)

Clear Cumul:

Resets (Clears) the following counters in the “Exec” front panel display: CV =

Cumulative Volume; RT = Run Time; Q1 = Filtrate Weight.

Response F:

Response Factor setting. The Pump Response Factor = 100 is the default value.

Increasing the Pump Response Factor will increase the pumps responsiveness to pressure
changes.

Pressure Zero:

Allows you to zero the backpressure readings of all 3 pressure sensors. The

FilterTec Plus pump must not be running when resetting pressure sensor output.

Alarm Enable:

Allows you to select alarm options for five (5) different alarm conditions. There

are 3 options available: 1. Disable the alarm

(Off);

2.Enable an auditory alarm

(Alarm Only);

Stop pump and provide an auditory alarm

(Pump Stop)

when user defined alarm limits are

exceeded. The Hi-Pressure Alarm has a fourth option:

Pmaintain

, which allows you to switch

from the rate control method to the pressure control method when running an R-Step or R-Scan
step.

Alarm Limits:

Allows you to assign alarm limits for several different alarm conditions:

Cumulative Volume

in milliliters;

Hi-Temperature in

⁰

Run Time

in hours:minutes;

Lo-Pressure

(monitor system leakage) in psi;

Hi-Pressure

(Monitor filter plug-up);

Lo-Flow

(high filter backpressure) in ml/min;

Filtrate Weight

in grams. (This alarm must be

enabled in order to obtain and display the
Filtrate Weight (FQ).)

The Lo-Pressure, Hi-Pressure and Lo-Flow alarms are related to the pressure source chosen in

SETUP: Press. Sensor, Source.

The Alarm condition is triggered when alarm limit is

exceeded.

Alarms are not mutually exclusive. You may select any combination of alarms.

Содержание SciLog FilterTec Plus









































































Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды

Parker SciLog FilterTec Plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SciLog FilterTec Plus

Отзывы:

Похожие инструкции для SciLog FilterTec Plus

Бренды по названию

Популярные бренды