Panasonic EBL512 G3 5000 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

54

can  be  "connected"  to  each  Addressable  Base  station  for
wireless  units  (4610).    Each  Base  station  shall  have  a
transmission  channel  (0-3)  selected.    The  Base  station's  COM
loop address is set on a DIL-switch.  The COM loop address for
the  wireless  detector  respectively  is  depending  on  the  Base
station's  COM  loop  address,  see  below.    Ext.  24  V  DC  power
supply  is  required.    For  more  information,  see  the  Technical
Description and the Product Leaflet.  See also drawing 512 G3
– 31.

9.1.7

COM loop addresses for Base station and Wireless
detectors

Each Base station takes one COM loop address (012 in the example
below).

Each wireless detector's COM loop address will be as follows:

Detector

COM loop address

address

0

Base station's COM loop a1 (e.g. 012+1=013)

1

Base station's COM loop a2 (e.g. 012+2=014)

..and so on..

15

Base station's COM loop a16 (e.g. 012+16=028)

NOTE!

Since the highest possible COM loop address is 255 the

highest possible COM loop address for a Base station is 239 if 16
Wireless smoke detectors shall be supported (239+16=255).

9.2

Units connected to the RS485 interface

Up to sixteen

D

isplay

U

nits type Ext. FBPs (1826 / 1828) and/or Alert

Annunciation  Units  (1735  /  1736)  and/or  Ext.  Presentation  Units
(1728) can be connected to the built-in RS485 interface (J4:37-38) in
EBL512 G3.  Note that the current consumption for 1826 with printer
can  be  up  to  200  mA  when  printing.    (Power  supply  at  J4:35-36.)
Connections, see drawing 512 G3 – 24.

NOTE!

Display Unit software version > 1.4.0 is required.

Address and S/W mode settings

The display and the push buttons (in the unit respectively) are used to
set the address, which also can be changed via EBL512 G3. The S/W
mode shall be set to

xxxx – 1587

(

xxxx

= type number). See the

Technical Description for the unit respectively.

The first unit shall have the address 00, the second unit address 01 and
so on

44

. Follow the Address setting instructions in the Technical

Description for the unit respectively.

44

The connection order on the line is not dependent of the address.

«
...
54
55
56
57
58
...
»

Содержание EBL512 G3 5000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EBL512 G3 5000

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: Bartlett Страницы: 30

Бренд: Eaton Страницы: 12

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Бренд: National Instruments Страницы: 78

Бренд: Newport Страницы: 417

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Бренд: SILENTRON Страницы: 20

Бренд: MacroAir Technologies Страницы: 32

Бренд: Atmel Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды