Panasonic EBL512 G3 5000 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

49

connected to  the  COM  loop  but  max.  10  per  COM  loop.    Red
ABS plastic housing and PC lens.  Low (0.5 Cd) or high (1 Cd)
light output  is programmable.  An output control expression is
programmed  (via  WinG3).    For  more  technical  data,  see  the
Product Leaflet.

The  COM  loop  address  is  set  with  the  Address  setting  tool
(3314).    The  beacon  has  an  address  label  on  which  the
programmed address can be written.
The Address setting tool (3314) is also used for mode setting:

NORMAL mode

: Used for 4380 in system EBL512 G3.

2330 mode

: Not used in system EBL512 G3.

2312 mode

: Not used in system EBL512 G3.

9.1.4

Short circuit isolators (addressable)

Each COM loop short circuit isolator

is to be programmed (via

WinG3) regarding:



COM loop address



Name (Normally not changed)



Sequence Number (Serial Number in the COM loop's A-
direction.)

Connections, see dwg 512 G3 - 31. (See especially the

L

/ SA wire!)

4313

Analog base with isolator.

39

4313 is an analog base with a

built-in  short  circuit  isolator.  In  case  of  short  circuit  on  the
COM  loop,  the  number  of  disabled  units  will  be  minimised.
4313  is  power  supplied  via  the  COM  loop.  For  more
information, see the Product Leaflet.  The COM loop address is
set  with  the  Address  setting  tool  (3314).    The  unit  has  an
address label on which the programmed COM loop address is to
be written.
The Address setting tool (3314) is also used for mode setting:

NORMAL mode

: Used for 4313 in system EBL512 G3.

2330 mode

: Not used in system EBL512 G3.

2312 mode

: Not used in system EBL512 G3.

According to the EN54 standard, at least one short circuit isolator is
required per 32 alarm points on the COM loop. In the Australian and
New Zealand conventions at least one isolator per 40 alarm points.

Up to sixteen 4313 can be used, which gives seventeen loop segments.
Each  isolator  has  to  be  given  a  Sequence  Number,  00-15.    The
isolators  have  to  be  connected  consecutively  (Sequence  Number  00-
01-02-03-04-05-06-07-08-09-10-11-12-13-14-15)  in  the  COM  loop's
A-direction.

NOTE!

EBL512 G3 has one built-in isolator in the-A

direction (no. "A") and one in the B-direction (no. "B").

39

This unit has replaced the Addr. isolator 4370.

«
...
49
50
51
52
53
...
»

Содержание EBL512 G3 5000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EBL512 G3 5000

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: Canon Страницы: 2

Бренд: Parkside Страницы: 65

Бренд: RADEMACHER Страницы: 48

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Savant Страницы: 2

Бренд: Monster Central Страницы: 13

Бренд: Rain Bird Страницы: 18

Бренд: Whale Страницы: 8

Бренд: Tascam Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды