Panasonic EBL512 G3 5000 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

111

(nuisance alarms) since all conventional smoke detectors (except
4350, see page 123) have a fixed fire alarm level. Conventional
smoke detectors have no service signal output and have to be replaced
on a regular basis (i.e. before being too contaminated).

Analog smoke detector: The sensitivity will automatically be
constant.

107

Service signal

will be activated at a fixed

service level

.

For detectors 4300 and 4301 (in NORMAL mode), Service signal will
be activated when the week average sensor value is > 1.8 %/m.

For more information, see EBL512 G3 Operating Instructions
MEW01163 chapter "Sensors activating Service signal (H4/U5)" and
"Acknowledge Service signal (H8/S3)".

16.26

Fault signal (fault condition)

Fault signal, fault messages, fault acknowledge, etc. are described in
EBL512 G3 Operating Instructions MEW01163, chapter "Fault".

Programmable inputs can be used to activate fault signal in the
EBL512 G3 c.i.e. See chapter "Programmable inputs", page 62.

16.27

Alarm texts

The alarm texts are shown in case of fire alarm.

When  a  fire  alarm  is  activated,  the  presentation  number  (Zone  –
Address)  will  be  shown  in  a  field  in  the  middle  of  the  c.i.e.  display.
On  the  row  just  below  the  presentation  number,  the  user  definable
alarm text for that alarm point will be shown, if programmed.

108

The

alarm text will also be presented in Ext. Fire Brigade Panels, etc. The
alarm text will be printed when a printer is available in the c.i.e or the
Ext. FBP.

See also EBL512 G3 Operating Instructions MEW01163, chapter
"Fire alarm".

The  alarm  texts,  up  to  40  alphanumeric  characters,  are  created  and
downloaded  via  WinG3.    Each  addressable  alarm  point  can  have  the
same  alarm  text  displayed  in  the  Ext.  FBP:s  1826  &  1828,  the  Alert
Annunciation  units  1735  &  1736  and  in  the  Ext.  Presentation  unit
1728 (or a different alarm text in each unit).  See also WinG3 help.

16.27.1

Creating the alarm texts via WinG3

For more information, see also WinG3 help.

107

The detector is supervised at all times and adapts its fire alarm level in

relation to the contamination of the detector, see chapter "Week average

sensor value", page 88.

108

See also chapter "Limitations", page 158.

«
...
111
112
113
114
115
...
»

Содержание EBL512 G3 5000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EBL512 G3 5000

Бренд: S&C Страницы: 40

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: K&K Страницы: 6

Minas A4 Series

Бренд: Panasonic Страницы: 5

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: Abicor Binzel Страницы: 8

Бренд: Unipulse Страницы: 99

Бренд: Accutrol Страницы: 25

Бренд: Mainpine Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Datavideo Страницы: 8

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: Lamtec Страницы: 22

Бренд: Parker Страницы: 42

Бренд: Warner Electric Страницы: 4

S3500 Series Uplink Module

Бренд: Aruba Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды