Panasonic EBL512 G3 5000 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

58

EBL512 G3.

Any fault in the system will be presented as "General fault in
system". The buzzer will sound.

45

It can be silenced. Any

disablement in the system will be presented as "General
disablement in system".

45

A  built-in  buzzer  will  sound  like  in  EBL512  G3.    The  buzzer
can be silenced but the alarm devices in the installation  cannot
be  silenced  via  this  unit.    New  software  versions  can  be
downloaded  directly  in  the  unit.    The  unit  is  power  supplied
from  EBL512  G3  or an  external  power  supply.    The unit  shall
run in

S/W mode 1728 – 1587

.

The number of units that can be power supplied via EBL512 G3
(or  an  external  power  supply)  is  depending  on  all  other  units
connected  to  the  same  c.i.e.  /  external  power  supply.    Up  to
1200 m cable can be used.  For more information, see Technical
description MEW00290.

9.2.4

German Fire Brigade Panels

FBP 2003

47

German Fire Brigade Control Panel (Feuerwehr-

Bedienfeld).    A  grey  metal  housing  (HxWxD,  185  x  255  x  58
mm) with a door. A key is required to open the door, which has
a  Plexiglas  ahead  of  the  front.    It  has  cable  inlets  on  the  top,
bottom and back sides and is intended to be wall mounted.

The function, LED indicators and push buttons on the front are
in accordance with DIN 14661.

The front's designation texts

are in German.

Serial RS485 interface for IHD protocol.

The unit is power supplied from EBL512 G3 (or an ext. power
supply). Up to 1200 m cable can be used.

FAT 2002

48

German Fire Brigade Indicator Panel (Feuerwehr-

Anzeigetableau).  A grey metal housing (HxWxD, 185 x 255 x
58 mm) with a door.  A key is required to open the door, which
has a Plexiglas ahead of the front.  It has cable inlets on the top,
bottom and back sides and is intended to be wall mounted.

The function, Display information, LED indicators and push
buttons on the front are in accordance with DIN 14662.

The

front's designation texts are in German.

Serial RS485

interface for IHD protocol.

The unit is power supplied from EBL512 G3 (or an ext. power
supply). Up to 1200 m cable can be used.

47

IFAM GmbH Erfurth, type FBF 2003.

48

IFAM GmbH Erfurth, type FAT 2002.

«
...
58
59
60
61
62
...
»

Содержание EBL512 G3 5000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EBL512 G3 5000

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Uclear Страницы: 40

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 157

Бренд: Samson Страницы: 78

Бренд: Valcom Страницы: 6

disklavier DKC-850

Бренд: Yamaha Страницы: 2

Бренд: Ziton Страницы: 36

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: Centurion Страницы: 16

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

Бренд: Nice Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды