Panasonic EBL512 G3 5000 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

57

Fire brigade alerted

, indicating that the "Fire brigade tx"

output is activated in EBL512 G3 because:

-

the activated fire alarm is not an

AA

alarm

-

the

AA

function has been ended, e.g. the acknowledge or

investigation time respectively has run out, etc.

Acknowledge

, indicating that the

AA

alarm has been

acknowledged.

The unit has the following push buttons:

Alarms queued

, used to scroll amongst the alarms.

Acknowledge

, used to acknowledge an

AA

alarm and hereby

also silence the buzzer.

Reset

, used to reset an

AA

alarm.

The unit shall run in

S/W mode 1735 – 1587

. Up to 1200 m

cable can be used. For more information, see Technical
description MEW00224.

1736

Alert Annunciation Unit (AAU). This unit is like 1735, except
it has a neutral front, where the

designation texts, in any

language

, are made separately and by production put into a

transparent "text slot" for the LED and push button respectively.
(This  front  also  holds  one  extra  LED  &  two  extra  push
buttons.).
The  unit  shall  run  in

S/W mode 1736 – 1587

. Up to 1200 m

cable can be used. For more information, see Technical
description MEW00224.

9.2.3

External Presentation Units

1728

External  Presentation  unit  (EPU).    A  compact  size  enclosure
(HxWxD, 145 x 220 x 50 mm) made of grey high impact ABS.
Fitted  with  a  supplementary  "O"  ring  gasket,  it  will  comply
with  IP61,  in  respect  of  dust  and  moisture.    The  unit  has  no
door,  i.e.  the  front  is  accessed  directly,  when  required.    The
push  buttons  are  disabled  until  they  are  supposed  to  be  used.
The  unit  shall  be  wall  mounted.    Two  compression  glands  are
attached.

The front's designation texts are in Swedish.

This

unit is intended for pre-warning, co-incidence

46

, fire (and heavy

smoke  /  heat)  alarm  presentation.    If  there  are  two  or  more
alarms in the system, you can scroll amongst them but the fire
alarms cannot be reset via this unit.
All  or  selected  alarms  will  be  presented  in  a  display  (alpha-
numeric LCD, 2x40 characters), with back-light.  An alarm text
will also be presented together with each alarm, if programmed
in EBL512 G3.  Furthermore, at least 617 texts can for selected
fire  alarms  be  stored  in  the  unit  and  will  in  such  a  case  be
shown, instead of the texts sent out from EBL512 G3 for these
alarms.  These text messages will be downloaded to the unit via

46

Two zone / address dependence.

«
...
57
58
59
60
61
...
»

Содержание EBL512 G3 5000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EBL512 G3 5000

Бренд: ABB Страницы: 63

Бренд: QUAD Страницы: 16

Бренд: Warren Controls Страницы: 16

Бренд: Harmonic Drive Страницы: 85

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Z3-DM8107-SDI-RPS

Бренд: Z3 Technology Страницы: 73

Бренд: Z-Wave Страницы: 14

Бренд: Z-Wave.Me Страницы: 4

Бренд: M-system Страницы: 13

Бренд: DSE Страницы: 2

Бренд: Ashly Страницы: 1

Бренд: OneFex Страницы: 24

Бренд: Lampert Страницы: 15

Devicenet R7F4HD-DAC32C

Бренд: M-system Страницы: 9

Бренд: Universal Remote Страницы: 10

Бренд: CAME Страницы: 128

Бренд: Data Aire Страницы: 137

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды