Panasonic EBL512 G3 5000 Скачать руководство пользователя страница 80

Страница: 80 / 168

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

Comments to the trigger conditions (functions):

Fire alarm. For more information regarding fire alarm,
see EBL512 G3 Operating Instructions MEW01163.

See 1.

Pre-warning.

For more information regarding pre-

warning, see EBL512 G3 Operating Instructions
MEW01163.

See 5.

Heavy smoke / heat alarm. For more information
regarding heavy smoke / heat alarm, see EBL512 G3
Operating Instructions MEW01163.

See 9.

One address (in two-address dependence) is in fire alarm
state. For more information, see EBL512 G3 Operating
Instructions MEW01163.

One zone (in two-zone dependence) is in fire alarm state.
For more information, see EBL512 G3 Operating
Instructions MEW01163.

Output activated when input trigger condition "Multiple
detector alarm" is true, i.e. fire alarm type A.

Output activated when input trigger condition "One
detector alarm" is true, i.e. fire alarm type B

One or more interlocking inputs, in the specified
interlocking area, are activated.

The interlocking input, in the specified interlocking
area/point, is activated.

One or more interlocking inputs are activated.

One or more interlocking inputs, in the specified range,
are activated (from interlocking area no./point to
interlocking area no./point).

Routing equipment output (any Fire brigade tx output) is
activated.

Routing equipment output (Fault tx) is activated.

The trigger condition is true as long as the pre-warning level is exceeded.

It is also true as long as the fire alarm level is exceeded even if the option

pre-warning detection is disabled (via WinG3).

See chapter "Fire alarm type A and Fire alarm type B", page 104.

Indicated by LED "Fire brigade tx". Output can be tested via menu H1.

This trigger condition

must not

be used for type of output "Routing

equipment (Fire brigade tx)".

Содержание EBL512 G3 5000









































































































































































Результаты поиска

Содержание EBL512 G3 5000

Отзывы:

Похожие инструкции для EBL512 G3 5000

Бренды по названию

Популярные бренды

Panasonic EBL512 G3 5000, Руководство по планированию

Результаты поиска

Содержание EBL512 G3 5000

Отзывы:

Похожие инструкции для EBL512 G3 5000

Бренды по названию

Популярные бренды