Panasonic EBL512 G3 5000 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

129

Set the wanted number and the validation check in WinG3 can give a
"too many alarm points" warning. The validation check is
automatically performed when starting a download of SSD to the c.i.e.



Suppress buzzer during fault

: This check box shall be marked

if faults generated in other control units shall be suppressed in this
control unit, i.e. if the buzzer shall sound for faults generated in
this control unit only.



Use Pre-warning

: This check box shall be marked if the pre-

warning detection shall be enabled, i.e. pre-warnings will be
activated in this control unit and presented in all control units. All
programmable outputs in the system, with trigger condition "Pre-
warning", will be activated (if not disabled).

Checkbox not marked = Pre-warnings will not be activated in this
control unit.

19.2

WinG3 Control unit pop-up menu

Some commands might be disabled since you have to connect and log
on to the control unit to be able to select / use them.

19.2.1

Reset alarm counter

The control unit has an alarm counter that can be reset if required.

19.2.2

Software version

The control unit software (S/W) version will be displayed.

19.2.3

Upgrade number of alarm points

The control unit is by delivery be configured for 128, 256 or 512
alarm points. Any number of

alarm points

can be changed on site,

normally 128



256



512.

«
...
129
130
131
132
133
...
»

Содержание EBL512 G3 5000









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EBL512 G3 5000

Бренд: Warren Controls Страницы: 16

Бренд: UNITED Страницы: 22

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: Lawler Страницы: 5

Бренд: Eaton Страницы: 8

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 56

Бренд: SYR Страницы: 2

Бренд: Data Signs Страницы: 23

Бренд: FUTABA Страницы: 8

Бренд: Scanreco Страницы: 10

Бренд: Teledyne Страницы: 102

SYNCHRO QUASAR AC

Бренд: UCS Страницы: 10

MultiMode 1214-8

Бренд: Curtis Страницы: 41

Бренд: FUHR Страницы: 20

Бренд: Water Specialist Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды