Panasonic AJ-HPM200P Скачать руководство пользователя страница 179

Страница: 179 / 230

Setup: Item Settings

179

S
e

Panasonic camera-recorders, recording formats and recording/stopping signals (Recording Mark)

Only recording format of 1080/**i is available.

170

AVCHD REC

0000

0001

OFF

Selects whether to make an AVCHD recording to an SD card simultaneously with

recording to a P2 card.

0: No AVCHD recording

1: Makes an AVCHD recording to an SD card simultaneously with recording to a P2 card.

NOTE:

• Displayed only when an AJ-YCX250G AVCHD codec board (optional) is installed.

• AVCHD recording is not available when 480i or 576i is set in setup menu No. 020 (SYS

FORMAT). Select up-conversion recording to record 480i and 576i input as AVCHD.

• Use the setup menu No.774 (AVCHD A CH) to select channels to record.

• The start and end of recording may not match the clip recorded on the P2 card.

• AVCHD recording is not available when setup menu No. 041 (LOOP REC) is set to

ON.

Model

Recording format

Recording Mark TYPE

Remarks

AJ-HDC27F, H

720/**p over 60p

TYPE1

AJ-HDX900

720/59.94p

720/23.98p over 59.94p

720/29.97p over 59.94p

720/50p

720/50p over 50p

1080/59.94i

TYPE1/TYPE2

When using in TYPE1, set UB_MODE on the

camera to FRAM_RATE. When using in TYPE2,

set VITC_UB_MODE on the camera to

FRAM_RATE.

1080/23.98p over 59.94i

1080/29.97p over 59.94i

1080/50i

1080/25p over 50i

AJ-HDX400P

1080/59.94i

AJ-HDX400E

1080/50i

1080/25p over 50i

AG-HPX500/502

AG-HPX170/171/172/174

AG-HPX300/301/302/304

AG-HPX370

AJ-HPX2000/2100

AJ-HPX3000

AJ-HPX2700

AJ-HPX3700

720/**p

1080/**i

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

180

BATTERY SEL

0000

0001

0002

0003

0004

0005

0006

NiCd12

NiCd13

NiCd14

S-LION

I-LION

TYPE-A

TYPE-B

Sets the battery type.

0: Settings for 1 pc. 12 V battery (NEAR: 11.2 V, END: 10.6 V)

1: Settings for 1 pc. 13 V battery (NEAR: 12.0 V, END: 10.6 V)

2: Settings for 1 pc. 14 V battery (NEAR: 13.6 V, END: 10.6 V)

3: Settings for 1 pc. lithium-ion battery (BP-L90A) (NEAR: 11.0 V, END: 10.6 V)

4: Settings for 1 pc. lithium-ion battery (ENDURA80) (NEAR: 13.4 V, END: 10.6 V)

5: Battery specified by setup menu No. 181 (TYPE-A NEAR) and No. 182 (TYPE-A END).

6: Battery specified by setup menu No. 183 (TYPE-B NEAR) and No. 184 (TYPE-B END).

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

59.94Hz

50Hz

only

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды