Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 170 / 230

170

Setup: Item Settings

SYSTEM FREQ

For AJ-HPM200P

Sets system frequency.

0: 59.94 Hz

1: 50 Hz

2: 23.98 Hz

3: 24 Hz

4: 29.97 Hz

5: 59-23 Hz

Receives 59.94 Hz input. Select this frequency to record 2:3 pull-down converted

(24-frame signal) output from VariCam: AJ-HDC27 series camera, AJ-HPX2700 or

other camera.

6: 60-24 Hz

Receives 60Hz input. Select this frequency to record 2:3 pull-down converted

(24-frame signal) output from VariCam: AJ-HDC27 series and AJ-HPX2700 series

camera.

7: 25 Hz

8: 60-25 Hz

Receives 60 Hz input. Select this frequency to record a variable frame rate set to 25p

from VariCam: AJ-HDC27 series camera.

0000

0001

0002

0003

0004

0005

0006

0007

0008

59.94

23.98

29.97

59-23

60-24

60-25

For AJ-HPM200E

0000

0001

0002

0003

0004

0005

0006

0007

0008

59.94

23.98

29.97

59-23

60-24

60-25

HD SYS H ADV

0000

0001

90H

Specifies whether or not HD SDI output should advance 90H phase relative to SD REF

input during SD REF input.

0: Outputs HD SDI at the same phase as SD REF.

1: HD SDI output is output at a phase that is 90H advanced relative to SD REF.

NOTE:

• The audio output and TC output are output in the same phase as HD SDI output.

• At 720p, the phase difference is 120H.

VDCP CMD

0000

0001

OFF

Determines whether the REMOTE connector should support the VDCP command.

0: Does not support the command

1: Supports the command

NOTE:

• When this setting is ON and REMOTE is also selected, the thumbnail screen cannot

be opened.

• When this setting is ON and REMOTE is also selected, recording is not available.

• When this setting is ON, external device control using the MODE button and PLAYER

button are disabled.

• When this setting is ON, the setup menu No. 050 (P.ON GUI) setting is disabled and

the thumbnail screen and playlist screen do not open when the power is turned on.

• When this setting is ON, SEARCH, FF and REW from an external device are ignored.

VDCP ID

0000

0001

0002

0003

0004

PRGNME

CLIPID

USRNME

SCNENO

CLPNME

Selects metadata that can be used as an VDCP ID.

0: Selects PROGRAM NAME.

1: Selects GLOBAL CLIP ID.

2: Selects USER CLIP NAME.

3: Selects SCENE NO.

4: Selects CLIP NAME.

NOTE:

• Variable-length IDs up to 64 bytes are supported. Other IDs are ignored.

• To enable changes of this setting, the unit must be restarted by turning the power on

and off.

MENU LOCK

0000

0001

OFF

Sets/releases the system file lock mode.

0: Releases the lock (file data can be changed)

1: Lock is engaged (file data cannot be changed)

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

59.94Hz

29.97Hz

only

59.94Hz

50Hz

only

59.94Hz

50Hz

only

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды