Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 25 / 230

Introduction: Control Reference Guide

In
tr

odu

tio

MENU/DIAG/OPERATION button

MENU button

Press this button to open the setup menu, thumbnail or

playlist menus. Press again to return to the previous

screen.

➝

Refer to “Moving Between Screens and Menu

Operations” (page 34).

Refer to “Setup” (page 166).

DIAG (SHIFT+MENU) button

When not in the thumbnail or playlist screen, press this

button to show information about this unit. Press again

to return to the previous screen. However, in the

thumbnail or playlist screen, it has the same effect as

pressing the OPERATION (SHIFT + MENU) button.

Information about this unit includes [VIDEO SYSTEM],

[WARNING], [HOURS METER], [UMID] and [DIF]. Use

the SET button or the right and left cursor buttons

(

) to switch among them.

OPERATION (SHIFT + MENU) button

In the thumbnail and playlist screen (when no menu is

displayed), press the SHIFT button and this button

simultaneously to show and select the [OPERATION]

menu.

LAST X/DELETE button

LAST X button

In the playlist mode, use this button to return a previous

editing operation.

➝

Refer to “Buttons Used in Playlist Operations” (page

88).

DELETE (SHIFT + LAST X) button

In the thumbnail or playlist screen, press this button to

delete the selected clip or event.

IN/SLOT CLIP/PF1 button

IN button

Use this button to perform the following functions

during clip playback or when the unit is controlled

externally.

• IN+ENTRY

Press the ENTRY button and this button to set an IN

point.

• IN

Press this button to confirm a set IN point. “--:--:--:--”

is displayed when no point has been set.

• IN+RESET

Press the RESET button and this button

simultaneously to delete the current IN point.

• IN+GOTO

Press the GOTO button and this button

simultaneously to cue up to the set IN point.

SLOT CLIP (SHIFT + IN) button

In the thumbnail screen, each simultaneous press of

the SHIFT button and this button switches the clip

display between a specific SLOT or selected clip.

PF1 button

In recording/playback mode, press this button after

pressing the PF button to start the setup menu

operation registered in the PF1 button.

TRIM – /SLOT SELECT – button

SLOT SELECT – (SHIFT + TRIM –) button

Hold down the SHIFT button and this button

simultaneously to move to the previous recording slot

position. Pressing this button when the unit is in slot 1

results in a move to slot 6.

TRIM – button

Use this button to move to a hard disk partition.

➝

Refer to “Displaying Clip Thumbnails on a Hard Disk”

(page 132).

Use this function for trimming.

➝

Refer to “Buttons Used in Playlist Operations” (page

88).

[VIDEO SYSTEM]

screen:

Shows current system

frequency, recording

format, input and output

formats and other

information.

[WARNING] screen:

Shows warning

information.

[HOURS METER]

screen:

Shows the unit serial

number, the number of

hours it has been on, and

the number of times it has

been switched on and off.

[UMID] screen:

Shows UMID information

for the current video.

[DIF] screen:

Shows various information

on the current DIF (the

IEEE 1394 interface).

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды