Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 38 / 230

Introduction: Recording, Playback and P2 Card Handling

Recording, Playback and P2 Card Handling

◆

NOTE:

• When you use this unit for the first time, be sure to set the internal

clock in setup menu No. 069 (CLOCK SET). (

➝

page 175)

Turn on the POWER switch of this unit.

Insert a P2 card in a P2 card slot, and push it in until

the EJECT button pops out.

Bend the protruding EJECT button downwards to the

right and set the card lock to ON.

• The P2 card access LEDs on this unit show P2 card status

when a P2 card is inserted.

➝

For details on P2 card status, refer to “P2 card access LEDs

and P2 card status” (page 39).

To start recording after a stop in the recording mode, press

the REC

button and the PLAY

button simultaneously.

Recording starts on the P2 card whose access LED lights

orange. Press the STOP

button to stop recording.

Press PLAY

to start playback.

Recording cannot be started from the thumbnail/playlist

mode.

➝

For details, refer to “Control Reference Guide” (page 20).

◆

NOTE:

• The P2 card access LED for a slot where a P2 card is inserted during

playback of a previously inserted card will remain off and the

second P2 card is not recognized. The second P2 card is

recognized when playback ends.

The continuous playback function, however, allows playback of all

the clips, including those in the P2 card inserted during playback.

➝

Refer to “Continuous Playback of Clips by Inserting/Removing P2

Cards” (page 57).

• A P2 card inserted in another slot during recording of a previously

inserted card will cause the P2 card access LED to flash and the

card will be recognized. Do not remove the P2 card from the slot

while it is being recognized.

• P2 cards are played back and recorded in the following slot order:

➝

• When the power is turned on and the slot selected for recording at

the last power off contains the same P2 card, that slot will again be

selected for recording. If the slot does not contain a P2 card or

contains another P2 card, a card in a slot with the lowest number will

be selected for recording.

• Slots can be selected also during recording.

When a slot could not be selected, for example, at the start of

recording or right after changing the P2 card slot used for recording,

“SLOT SEL INVALID” appears on the LCD monitor. Ongoing

LOOPREC and VFR recording also prevent selection of P2 card

slots.

• When a P2 card becomes full during recording, a slot with a higher

number that contains a card with free space will be selected for

recording.

• Format P2 cards only on a P2 card device.

• Recording is not available when setup menu No. 27 (VDCP CMD) is

ON during REMOTE operation.

Insert a P2 Card

OFF

CARD LOCK

①

OFF

CARD LOC

②

①

Recording and Playback

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды