Panasonic AJ-HPM200P Скачать руководство пользователя страница 191

Страница: 191 / 230

Setup: Item Settings

191

S
e

775

25M REC CH

0000

0001

2CH

4CH

Specifies the number of audio channels that will be used for DVCPRO (25 Mbps) or DV

(25 Mbps) recording.

0: Records on two channels.

1: Records on four channels.

NOTE:

DVCPROHD, AVC-Intra50 and AVC-Intra100 always record on 8 channels, and

DVCPRO50 always records on 4 channels.

776

REF LEVEL

For AJ-HPM200P

Specifies the standard level.

0: –20 dB
1: –18 dB

2: –12 dB

0000

0001

0002

FS-20

FS-18

FS-12

For AJ-HPM200E

0000

0001

0002

FS-20

FS-18

FS-12

777

CH2 MIC PWR

0000

0001

OFF

Turns on and off the CH2 microphone power supply.

0: Does not use the microphone power supply.

1: Uses the jack switch to turn the microphone power supply on and off.

778

AUD OUT DLY

0000

0001

OFF

Determines whether or not the output timing of analog audio output (including
headphones and monitor output) is delayed to synchronize it with SDI output.

0: Not delayed

The output is synchronized with LCD monitor and VIDEO OUT output.

1: Delayed

The output is synchronized with SDI output.

NOTE:

LCD monitor and VIDEO OUT are output about 66 msec earlier than SDI output.

782

EMBD CH SEL

0000

0001

0002

CH1-4

CH5-8

CH1-8

Selects channels to multiplex on the SD SDI output.

0: Outputs four channels (CH1-4).

1: Outputs four channels (CH5-8).

2: Outputs the CH1-8 channels.

NOTE:

• Four channels (CH1-4) are multiplexed during DVCPRO and DVCPRO50 playback.

• Some devices may not be able to receive 8 channels. Check the specifications of the

receiving equipment before setting CH1-8.

785

PB MIX

0000

0001

OFF

Sets a mix of analog and SDI audio output.

NOTE:

Press the STOP or SET button to open a subscreen and select the channels used in

mixing audio output. To exit the subscreen, press the STOP or SET button again.

Subscreen

PB CH1

000

001

002

003

004

005

006

007

CH1

CH1+2

CH1+3

CH1+4

CH123

CH124

CH134

CH1234

Specifies the playback channels that will be output via CH1.

0: Audio output of CH1

1: Audio output of CH1 and CH2

2: Audio output of CH1 and CH3

3: Audio output of CH1 and CH4

4: Audio output of CH1, CH2 and CH3

5: Audio output of CH1, CH2 and CH4

6: Audio output of CH1, CH3 and CH4

7: Audio output of CH1, CH2, CH3 and CH4

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

59.94Hz

50Hz

only

23.98Hz

24Hz

59-23Hz

60-24Hz

only

59.94Hz

50Hz

29.97Hz

25Hz

60-25Hz

only

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды