Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 60 / 230

Clip Management: Attaching Text Memos and Shot Marks

Attaching Text Memos and Shot Marks

A text memo can be attached in a clip to mark a specific

location. The user can attach shot marks to distinguish clips

from each other. This function is not available on cards where

the write protect switch has been set to PROTECT.

Use the NEXT and PREV buttons to locate attached text

memos during video playback.

➝

Refer to “Setup menu No. 103 (SEEK SEL)” (page 177).

Press the TEXT MEMO button during recording,

playback or when thumbnails are displayed.

• Press this button during recording and playback where

you want to attach a text memo.

• Pressing this button in the thumbnail screen adds a text

memo at the thumbnail clip location (normally at the

beginning).

◆

NOTE:

• Up to 100 text memos can be attached in one clip.

• Pressing the TEXT MEMO button during playback may

temporarily halt playback. This is normal and not a malfunction.

• Text memos are not recorded during LOOP REC or VFR ON

recording.

Press the THUMBNAIL button.

The thumbnail screen appears on the LCD monitor.

Press the MENU button and choose [THUMBNAIL] –

[TEXT MEMO CLIPS] from the thumbnail menu.

The thumbnails of clips with text memos appear at the top

of the thumbnail screen. Information on the selected clip

text memo appears in the lower half of the thumbnail

screen.

◆

NOTE:

• If an AVC-Intra clip has a different SYSTEM FREQ setting, the

thumbnail in the row below at the text memo location may be

replaced with

when a text memo clip appears.

Place the cursor on the clip (with a text memo) you

want play back and press the SET button.

The cursor moves to the lower half of the thumbnail

screen.

Attaching Text Memos

Playing back from text memo location

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

STILL/

PAUSE

REW

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

PLAYLIST

Thumbnail
display

Blue indicates selected
number of text memo

clips and white indicates

total number of text
memo clips.

Indicates still images
included with the text

memos.

The cursor moves.

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды