Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 174 / 230

174

Setup: Item Settings

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

026

PLY LST FMT

When set to 59.94 Hz

Specifies the format used by the playlist.

0: Format set in setup menu No. 020 (SYS FORMAT) and No. 025 REC FMT (HD).

1: 720/30PN (when set to 59.94 Hz)/720/25PN (when set to 50 Hz)

2: 720/24PN

0: Format set in setup menu No. 020 (SYS FORMAT) and No. 025 (REC FMT (HD)).

1: 1080/30PN (when set to 59.94 Hz)/1080/25PN (when set to 50 Hz) or 720/30PN (when

set to 59.94 Hz)/720/25PN (when set to 50 Hz)

2: 1080/24PN or 720/24PN

NOTE:

• When 480i or 576i is selected in setup menu No. 020 (SYS FORMAT), a 30PN and

24PN selection is handled as a SYSFMT setting.

• The number of lines in the AVC-Intra format depends on the setting in the setup menu

No. 020 (SYSFORMAT).

• When a selection other than 59.94 or 50 is made in setup menu No. 25 (SYSTEM

FREQ), the format selected in menu No. 020 (SYS FORMAT) and No. 025 (REC FMT

(HD)) is used.

• This AVC-Intra format also depends on the audio bit number setting in setup menu

No.034 (A.SMPL RES).

0000

0001

0002

SYSFMT

30PN

24PN

When set to 50 Hz

0000

0001

SYSFMT

25PN

028

AVCHD FMT

0000

0001

0002

0003

Specifies AVCHD recording rate.

0: PH mode (approx. 21 Mbps)

1: HA mode (approx. 17 Mbps)

2: HG mode (approx. 13 Mbps)

3: HE mode (approx. 6 Mbps)

NOTE:

• Displayed only when an AJ-YCX250G AVCHD codec board (optional) is installed.

• In 720P mode, recording is always made in PH mode.

031

OUT REF

0000

0001

0002

AUTO

REF

INPUT

Select reference for video output.

0: Uses the reference signal input to the REF connector as reference. When there is not

input to the REF connector, the selected video input signal is used as reference. When

there is no reference and video input signal, the internal clock is used.

1: The reference input signal is used as reference. If there is no such signal, the internal

clock is used.

2: The video input signal is used as reference. If there is no such signal, the internal clock

is used.

032

REC REF

0000

0001

NORMAL

SLTC

Specifies the reference to synchronize the frames for recording.

0: The input video signal is automatically identified and serves as reference.

1: The time code which is input to the SD I IN connector is identified and serves as

reference.

NOTE:

When the SLTC is selected, the following settings are necessary to validate the settings

for this item:

• Setup menu No. 25 (SYSTEM FREQ): 59.94

• Setup menu No. 020 (SYS FORMAT): 720p

• INPUT SELECT VIDEO button on the unit: HDSDI

59.94Hz

50Hz

only

59.94Hz

50Hz

only

59.94Hz

50Hz

29.97Hz

25Hz

only

59.94Hz

only

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды