Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 61 / 230

Clip Management: Attaching Text Memos and Shot Marks

C
lip

nag

eme

When the cursor is in the lower half of the thumbnail

screen, use the right and left (

) cursor buttons to

go to the thumbnail text memo you want to play back

and press the PLAY button.

The clip is played back from the text memo time code

location selected with the cursor.

When you press the STOP button to interrupt ongoing

playback, or when playback stops upon reaching the end

of the clip, the thumbnail screen reappears and the cursor

returns to the thumbnail text memo location where

playback was started.

Press the MENU button to select EXIT or press the EXIT

button and the cursor returns to the upper half of the

thumbnail screen.

◆

NOTE:

• During playback all buttons other than the STOP button are not

available.

Opening the text memo display from the thumbnail screen

allows you to delete text memos.

Open the text memo display from the thumbnail

screen.

Use the cursor buttons to move to the thumbnail for

which you want to delete the text memo and press

the SET button.

The cursor moves to the row below.

Select the thumbnail for witch you want to delete the

text memo and select [DELETE] from the menu.

Select [YES] in the confirmation dialog that appears.

The text memo is deleted.

Attach shot marks to distinguish clips from each other.

Open the thumbnail screen.

Use the cursor buttons to place the cursor on the

desired clip.

Hold down the SHIFT button and press the TEXT

MEMO button.

Each press of this button turns the shot mark indicator on

and off.

◆

NOTE:

• When attaching or deleting shot marks for clips that span

multiple P2 cards, be sure to load all the P2 cards that the clip

is recorded on.

• Shot marks cannot be added or deleted during loop recording.

Deleting text memos

Attaching Shot Marks

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

STILL/

PAUSE

REW

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

PLAYLIST

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды