Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 210 / 230

210

For Long and Trouble-Free Operation: Error Messages

This warning appears only during recording. Then the audio is recorded mute.

This warning appears only during recording. The internally generated time code is recorded.

P2 card access from the network is not available in normal operating mode.

Operation continues but normal recording or playback may not be possible.

This warning appears at any time. This error disables input to the digital video interface.

“E-50” appears when the backup battery is depleted. Consult your supplier for information on a store that can provide you with a new battery

(CR2032 or the equivalent). Be sure to use setup menu No. 069 (CLOCK SET) to set the clock after battery replacement.

INVALID AUDIO SIG

Displayed when the audio data of a signal input from the 1394 interface is irregular.

Operation

continues

INVALID TC SIG

Displayed when the time code data of a signal input from the 1394 interface is irregular. Operation

continues

REC WARNING

Displayed when a video or audio error occurs during recording.

To continue operation, turn the power off and then back on again.

STOP

CARD

ERROR<******>

Displayed when data was corrupted due to a P2 card error during recording.

This error is displayed after recording ends and remains on until the start of the next

operation.

Displayed when a load error occurs from a P2 card during playback.

(* indicates the slot number where the error occurred.)

Replace the P2 card in the slot where the error occurred.

STOP

LAN NO LINK

Displayed in normal operating mode when there is a problem in the LAN connections.

Check the LAN connections.

Operation

continues

NET ERROR

The FTP server service is not started up in normal operating mode.

Check the network settings.

Operation

continues

LAN ERROR

Displayed when a LAN connection or disconnection failed. Power off, then power up

again before use.

Should E-49 appear again, consult your supplier.

STOP

BATTERY EMPTY

Displayed when a drop in the backup battery voltage for the internal clock is detected at

power on. Replace the internal battery.

Operation

continues

DIR NG

CARD<******>

The P2 card directory structure is not supported. (* indicates the slot number where the

error occurred.) Make a quick backup of card data and format the card.

Operation

continues

RUNDOWN

CARD<******>

The maximum number of overwrites has been exceeded. (* indicates the slot number

where the error occurred.) This P2 card should be replaced.

Operation

continues

HDD INTERMITTENT

Displayed for 3 seconds when a dropout due to reduced hard disk performance occurs

during hard disk playback for monitoring purposes.

Use a faster hard disk.

Operation

continues

NOT 1× 100M SIG

Displayed when a signal input from the 1394 interface is not a DVCPRO HD (100 Mbps)

1× normal speed transfer signal.

Recording is

disabled

COPY PROTECTED

Displayed when DV format recording is available and the copy guard signal input via the

1394 interface is in the copy inhibit mode.

Recording is

disabled

1394 INITIAL ERROR

Displayed when the 1394 interface connection is irregular.

INVALID TC MODE

Appears during playback when the time code has been recorded in drop frame mode.

The video output is distorted and audio output is muted at the drop point of the time code.

Check the playback clip. Playing back a 24p frame-rate clip requires that the time code

be recorded in non-drop frame mode. Appears when the time code in an HD SDI input is

in the drop frame mode during EE or recording. Normal recording will not be possible

under these conditions. Check signal input to the unit. Set the input time code to non-drop

frame mode. (Appears when 23.98, 24, 59-23, 60-24 or 60-25 is set in setup menu No. 25

(SYSTEM FREQ).)

Operation

continues

INVALID EMBEDDED

Displayed while synchronizing recorded video frames to the time code of a signal input

to the HD SDI connector when that time code is not advancing at 1× normal speed. (When

“SLTC” is selected in setup menu No. 032 (REC REF) or 29.97, 59-23, 60-24, 25 or 60-25

is selected in setup menu No. 25 (SYSTEM FREQ).)

Operation

continues

Display

Description

Deck operation

Character code

23.98Hz

24Hz

59-23Hz

60-24Hz

60-25Hz

only

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды