Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 197 / 230

S
e

Setup: Time Code, User Bit and CTL

197

Time Code, User Bit and CTL

The time code is used when the time code signal generated

by the time code generator is to be recorded. The time code

values are indicated on the display and in the superimpose

display.

User bit refers to the 32-bit (8 digits) data frame of the time

code signal made available to users. It allows you to record

operator numbers and other values. The alphanumeric

characters that can be used in the user bit are the figures from

0 - 9 and the letters A to F.

Engage the stop mode.

Use the COUNTER button to select [TC].

Use the setup menu No. 504 (RUN MODE) to set the

run mode for the time code generator.

Set the TCG switch to PRESET mode.

Use the TC PRESET button to set the start value of

the time code or user bit.

Press the TC PRESET button.

The left-most digit starts flashing.

Press the up or down cursor button (

▲

▼

) or hold

down the STILL

button and turn the search dial

to change the value.

Press the left or right cursor button (

) or turn the

search dial to select digit to set.

The selected digits start flashing.

The setting ranges are as follows:

Repeat steps 2 - 3 to change other values.

Pressing the RESET button resets the preset value to 0.

When the start value is set, press the SET button.

The time code starts to advance when [FREE] is set in

step 3.

Time code

User bit

Setting the internal time code

TCR 00:

07:

04:

Hours Minutes Seconds Frames

OFF

METER

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB
MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

PLAYER

STOP

STILL/

PAUSE

PREVIEW

A.LEVEL REC

REW

REC

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

PLAYLIST

REC:

The internal time code generator advances

during recording.

FREE:

The internal time code generator advances

regardless of operating mode when the

power is on.

INT-REGEN:

This mode maintains the continuity with

the time code last recorded on a P2 card.

INT-PRESET:

Starts recording from the value set with

the TC PRESET button.

EXT:

Records according to external TC input.

Time code:

[59.94 Hz] [29.97 Hz]

00:00:00:00-23:59:59:29

[50 Hz] [25 Hz] [60-25 Hz]

00:00:00:00-23:59:59:24

[23.98 Hz] [24 Hz] [59-23 Hz]

[60-24 Hz]

00:00:00:00-23:59:59:23

User bit:

00000000-FF FF FF FF

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды