Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 125 / 230

Connections: Using This Unit With a Hard Disk

125

Con

nec

ons

(Hard disk types and available functions)

Adding clips to a partition will prevent writing back data by the card to that partition.

This enables up to 100 folders in up to three levels. Folders appear in order from the top level. Long file names and two-byte character file

names are not supported.

Example:

Audio and video dropouts may occur during playback due to hard disk performance and operating conditions. Perfect playback cannot be

guaranteed.

Select clips on the playlist player to edit clips on a hard disk.

◆

NOTE:

• Use hard disks under the following conditions.

- Operate hard disks within its specified operating conditions (temperature, etc.).

- Do not use hard disks in locations that are unstable or exposed to vibration.

• Normal operation may not possible with some hard disks and cables.

• Use a hard disk with sufficient space for copying.

• Do not connect multiple hard disks to the unit via a hub, for example, even when the other hard disks are powered off. In addition, do not

connect other devices to the unit via a hub when a hard disk is connected.

• During formatting and copying, do not disconnect cables, do not remove a P2 card that is involved in any of these activities and do not power

off this unit and the hard disk. Otherwise this unit and the hard disk must be rebooted.

• A hard disk is a high-precision instrument whose read and write functions may fail if used in an unsuitable environment. Please note that

Panasonic accepts no liability whatsoever for data loss or other losses either direct or indirect arising from hard disk damage or other defects.

• When data from this unit is copied to a hard disk and is edited on another computer, the data may no longer work in this unit and hard disk

data may become corrupted.

• Repair bad clips on P2 cards before copying them to a hard disk.

• SATA (serial ATA) or PATA (parallel ATA) interface hard disks connected using a USB converter cable may not be recognized.

• Do not connect or disconnect cables during recording or playback with the unit. Recording or playback may not occur normally if you do.

• On some hard disks, the initial playback confirmation after connecting a hard disk may take time.

Hard

disk type

Features

Available functions

Thumbnail

display

P2 card unit

Clip unit

Playback

check

Use of

playlists

Displaying

clips

Format

➝

HDD

➝

HDD

➝

TYPE S

A special disk format for high-speed

writing/loading data by P2 card unit.

P2STORE The P2 Store (AJ-PCS060G) hard

disk. Cannot be used for writing data.

FAT

A hard disk whose primary partition

is formatted either using FAT16 or

FAT32.

The root partition or “CONTENTS”

directory under any directory is used.

OTHER

Hard disk other than those above

NTFS or other hard disk using a file

system other than FAT16 or FAT32.

/CONTENTS

Can be displayed

/SAMPLE/CONTENTS Can

displayed

/SAMPLE/20090101/CONTENTS

Can be displayed

/SAMPLE/20090101/1200/CONTENTS

Cannot be displayed

➝

This is the fourth level and will therefore not appear.

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды