Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 24 / 230

Introduction: Control Reference Guide

PLAY LIST button

Press to start or end playlist mode.

➝

Refer to “Playlist Function” (page 80).

THUMBNAIL button

Press this button and the button lights, and the

thumbnail screen appears on the LCD monitor. Press

again to return to video playback and the button goes

out.

Setting setup menu No.051 (GUI OUTPUT) allows you

to transfer the thumbnail screen and the playlist screen

to the video output.

Cursor buttons (

)

The four outer buttons are cursor buttons. Use them to

move the cursor in thumbnails, menus, events, etc. The

SET button at the center is used to select menu items

and clips.

In the thumbnail or playlist screen, hold down the

SHIFT button and press a cursor button to move the

cursor to the beginning or the end. Or hold down the

SHIFT button and press the SET button to select

multiple clips or events.

Holding down the SET button in the (recorder) playlist

screen, selects or cancels all track events with the

same IN and OUT points as the event at the cursor.

EXIT/CANCEL/PF button

GUI Operations

OFF

POWER

METER

FULL/FINE

MONITOR

SELECT

METER SELECT

INPUT SELECT

REC

THUMBNAIL

SET

MENU

ENTRY

SLOT CLIP

PF1

ALL CLIP

PF3

SHIFT

PF4

CLIP LIST

PF2

SLOT SELECT

LAST X

TRIM

DELETE

VIDEO

GO TO

OUT

EDIT MODE

A.DUB

MODE

DIAG

OPERATION

EXIT

CANCEL/PF

MULTI

SEL

CH 1

CH 2

CH 3

CH 4

TEXT

MEMO

TCG

TC PRESET

PROP

RESET

COUNTER

PLAYER

STOP

STILL/

PAUSE

PREVIEW

A.LEVEL REC

REW

REC

PREV

NEXT

PLAY

REVIEW

1 CLIP PLAY

SOURCE SELECT

NEW

INT

REGEN

PRESET

EXT

MARKER

VAR

UNITY

VIDEO AUDIO

CH 1-4 CH 5-8

MODE

CONTROL

REMOTE
LOCAL

UNITY

2 4

UNITY

1 3

∞

2/4

CH
1/3

PLAYLIST

1
2

16 15 14 13

9 10 11 12

When the PLAYLIST/

THUMBNAIL buttons

are lit:

Press this button to return

from clip property, card

status or HDD thumbnail to

the previous screen.

Selecting [EXIT] in a menu

has the same effect as

pressing the SET button.

Press the SHIFT button and

this button simultaneously

to cancel a selection.

When the PLAYLIST/

THUMBNAIL buttons

are off:

Press this button to use the

7 (IN), 9 (ENTRY), 11 (OUT)

and 12 (SHIFT) buttons as

PF1 to PF4, respectively.

Press this button again

before pressing another

button and this mode will

close after a short interval.

➝

Refer to “Making

changes using the PF

buttons” (page 167).

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды