Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 91 / 230

Editing: Playlist Function

iti

ALL CLIP (SHIFT + OUT) button

During player thumbnail operation, hold down the

SHIFT button and press the OUT button to change to

display ALL clip types.

➝

Refer to “Changing Thumbnail Display” (page 51).

For details on other operations, refer to the

descriptions of the ENTRY button, TRIM+ /– button,

RESET button and GO TO button.

17.

ENTRY/CLIP

➝

LIST button

ENTRY button

Press to confirm trimming of IN and OUT points.

IN/OUT + ENTRY buttons

Hold down the IN or OUT button in the player or

recorder and press the ENTRY button to set the current

playback location as the IN or OUT point.

CLIP

➝

LIST (SHIFT + ENTRY) button

Inserts a clip selected in a player thumbnail at the

recorder IN point of the event at the cursor location.

18.

PLAY/REVIEW button

PLAY button

Use to play back video on the player or recorder.

REVIEW (SHIFT + PLAY) button

Use to review playback of event at the cursor location

or temporarily registered event during recorder

operation.

19.

STILL/PAUSE button

Displays still image on player or recorder. In A.DUB

mode, use this button to enter A.DUB/PAUSE status.

The menu does not open in playback mode. Nor are

the edit buttons available. Press the STOP button to

enable editing.

➝

Refer to “Recording Voice-Overs” (page 109).

20.

REC button

Finalizes an edit operation, registers the event and

displays it on the timeline. Imports video to a P2 card

from an external device (RS-422A), an external input

(live recording), or hard disk used as the player.

Use the REC + PLAY button during playback in the

A.DUB mode to start voice-over recording.

➝

Refer to “Recording Voice-Overs” (page 109).

21.

PREVIEW/A LEVEL REC buttons

PREVIEW button

Use this button to preview playback of event that is

being registered. Before the preview, the event is

registered and appears on the timeline. When the

player is a P2 card, the level changes made using the

fader operation during a preview are set in a registered

event.

➝

Refer to “Setting Audio Level” (page 113).

◆

NOTE:

• Events created from external devices or hard disks are

indicated in orange as temporarily registered events.

• Preview playback is disabled for an external input (live

recording).

A LEVEL REC (SHIFT + PREVIEW) button

Press this button to enable adjustment of the audio

level with the fader simultaneous with a preview of the

IN and OUT points of the recorder. This mode allows

you to dynamically change the audio level in the event.

➝

Refer to “Setting Audio Level” (page 113).

22.

SHIFT button

This button is used in combination with other buttons.

23.

UNITY/VAR/channel select switches and audio

playback level adjustment fader controls

Use the switches to select channels and the fader

when adjusting audio level during playback or when

recording voice-overs (mixing the original playback

sound with an additional recording).

◆

NOTE:

• Levels cannot be adjusted during playback of a playlist.

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды