Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 211 / 230

For Long and Trouble-Free Operation: Error Messages

211

r L

ong

and

le-

ree
O
per

ion

An attempt to start recording causes the button to temporarily light. It goes out a few seconds later and no recording is made.

The following warning messages appear when an incorrect operation is attempted in the thumbnail playlist screen.

Display

Description

Deck operation

Character code

INVALID TC

SEQUENCE

Appears during playback when frame rate data in user bit cannot be detected or when

the playback time code is not continuous. The video output is distorted and audio output

is muted in sections where the time code is not continuous. Check the playback clip.

Appears during EE or recording when frame rate data cannot be detected in the user bit

data in an HD SDI input or when the input time code is not continuous. Normal recording

will not be possible under these conditions. Check signal input to the unit. Input signals

with a matching time code and pull-down sequence (Appears when 23.98, 24, 59-23, 60-

24 or 60-25 is set in setup menu No. 25 (SYSTEM FREQ).)

Operation

continues

NO ACTIVE FRAME

Appears when active frame data cannot be detected in the user bits in the HD SDI input
during EE or recording. Normal recording will not be possible under these conditions.

Check signal input to the unit. The input signal must contain the active frame data from a

variable frame-rate camera. (Appears when 29.97, 59-23, 60-24 or 60-25 is set in setup
menu No. 25 (SYSTEM FREQ) and setup menu No 040 (VFR REC) is set to ON.)

Recording is
disabled

Operation

continues during
recording

INVALID FRAME

RATE

Appears when active frame data detected from the user bit in the HD SDI input during EE

and recording exceeds 50p. Normal recording is not possible under these conditions.
When SYSTEM FREQ is set to 60-25, set the frame rate on a variable frame-rate camera

to 50p or less. Appears when SYSTEM FREQ is set to 60-25 and VFR REC is set to ON.

Operation

continues

Item

Message

Description

Measure

Thumbnail

CANNOT ACCESS

GATEWAY!

CHECK LAN SETTING

Cannot access gateway server.

Check if LAN setup is correct.

CANNOT ACCESS!

Data cannot be accessed because it is corrupted

or for other reasons.

Restore media and clips to normal state before

access. When displayed during network operation,

check LAN setup, make sure the LAN cable is
correctly connected and check that your network

environment is functioning properly.

CANNOT ADD! NO
INPUT

User name or password in not entered correctly. Enter user name or password correctly.

CANNOT CHANGE!

A thumbnail containing a grayed out text memo that

cannot be generated is not available for editing.

Edit settings or content to enable thumbnail display.

CANNOT CONNECT! Connection to the network cannot be established. Check LAN setup, make sure the LAN cable is

correctly connected and check that your network

environment is functioning properly.

CANNOT CONVERT!

Inconvertible clips are included.

Check the selected content.

CANNOT DELETE!

Contents version mismatch prevents deletion.

Match devices and contents version.

CANNOT FIND
FTP-SERVER!

FTP server cannot be found.

Check if FTP client URL is correct.

CANNOT FORMAT!

P2 card problem prevents formatting.

Check P2 card.

CANNOT
RE-CONNECT!

A clip that does not span multiple cannot be
reconnected.

Check selected content.

CANNOT REPAIR IN

SELECTION!

Some of the selected clip could not be repaired.

CANNOT REPAIR!

Selected content cannot be repaired.

Check selected content.

CANNOT SAVE!

FILE NAME IN USE

A network setup file with the same file name

exists on the SD memory card.

Save to a different name.

CARD FULL!

The P2 or SD memory card is full.

Insert media with sufficient capacity.

INVALID VALUE!

Entered data was invalid.

Enter data in a valid range.

IP ADDRESS IS
USED!

The set IP address is used on another device.

Consult the network administrator, and set another
IP address.

LACK OF REC

CAPACITY!

There is not enough recording capacity left on the

card.

Insert a card with sufficient recording capacity.

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды