Panasonic AJ-HPM200P Скачать руководство пользователя

Страница: 175 / 230

Setup: Item Settings

175

S
e

034

A.SMPL RES

0000

0001

16BIT

24BIT

0: Audio recording is made in 16-bit.

1: Audio recording is made in 24-bit.

NOTE:

• When 24BIT is selected, the following settings are also required to make the 24BIT

setting valid.

– Setup menu No.020 (SYS FORMAT): 1080i or 720p

– Setup menu No.025 (REC FMT (HD): AVC50 or AVC100

040

VFR REC

0000

0001

OFF

Specifies whether or not to make a VFR recording when the recording format is 720p.

0: Does not make VFR recording

1: Makes VFR recording

➝

Refer to “Variable Frame Rate-Recording” (page 44).

041

LOOP REC

0000

0001

OFF

Specifies whether or not to make loop recording.

➝

For details, refer to “LOOP REC Function” (page 40).

0: Does not make loop recording

1: Makes loop recording

NOTE:

Turning the power off cancels this setting. The unit will then start up using the default

value (OFF) next time it is powered up.

050

P.ON GUI

0000

0001

0002

OFF

THUMB

PLYLST

Specifies whether or not the thumbnail screen or playlist screen appears when the power

is turned on.

0: Does not display thumbnail screen and playlist screen.

1: Displays the thumbnail screen.

2: Displays the playlist screen.

NOTE:

Always OFF when setup menu No. 27 (VDCP CMD) is ON.

051

GUI OUTPUT

0000

0001

0002

LCD

LCD&V

ALL

Specifies whether the GUI screen will be output to VIDEO OUT or SDI OUT connector.

0: Not output (displayed only on LCD monitor)

1: Output to VIDEO OUT connector

2: Output to both VIDEO OUT and SDI OUT connectors

NOTE:

• When 23.98 or 59-23 is selected in setup menu No. 25 (SYSTEM FREQ), the refresh

of the GUI screen output to SDI OUT may seem unnatural. Also, when the GUI screen

switches to the video screen (and vice versa), the output signal may be distorted.

• Some characters on the GUI screen output to VIDEO OUT may not be clear.

053

UNFOCUS SCRN

0000

0001

DARK

NORMAL

Specifies whether or not to decrease the brightness of the screen that is not selected on

the playlist screen.

0: Decreases the brightness of the screen not selected on the playlist screen.

1: Retains the brightness of the screen not selected on the playlist screen.

069

CLOCK SET

Sets the internal clock.

NOTE:

Press the STOP or SET button to open the subscreen for setting the time. Change the

date in the subscreen and press the SET button to set the clock date. To exit the

subscreen without setting a date, press the STOP or EXIT button again.

Subscreen

YEAR

0000

0037

2000

2037

Sets the year.

MONTH

0001

0012

JAN

DEC

Sets the month.

NOTE:

Setting a nonexistent day for February, April, June, September and November will

automatically set the equivalent day in the following month.

Item

Setting

Settings and brief function description

No.

SUPER

DISP.

No.

SUPER

DISP.

29.97Hz

59-23Hz

60-24Hz

60-25Hz

only

59.94Hz

50Hz

23.98Hz

29.97Hz

59-23Hz

25Hz

60-25Hz

only

Содержание AJ-HPM200P







































































































































































































































Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды

Panasonic AJ-HPM200P, Инструкция по эксплуатации

Результаты поиска

Содержание AJ-HPM200P

Отзывы:

Похожие инструкции для AJ-HPM200P

Бренды по названию

Популярные бренды