manualshive.com logo in svg

NEC V850/SB1, Руководство пользователя

"NEC V850/SB1" - мощный микроконтроллер, предназначенный для широкого спектра применений. На нашем сайте вы можете бесплатно скачать руководство пользователя для этого устройства. Загрузите его сейчас с manualshive.com.

Поделиться
Скачать
background image

CHAPTER  19    IEBus  CONTROLLER  (V850/SB2)

User’s Manual  U13850EJ6V0UD

565

(4) IEBus partner address register (PAR)

(a) When slave unit

The value of the receive data in the master address field (address of the master unit) is written to this

register.

If a request “4H” to read the lock address (lower 8 bits) is received from the master, the CPU must read

the value of this register, and write it to the lower 8 bits IEBus data register (DR).

If a request “5H” to read the lock address (higher 4 bits) is received from the master, the CPU must read

the value of this register and write the data of the higher 4 bits to DR.

Sets the partner address (12 bits) to bits 11 to 0.

15

0

14

0

13

0

12

0

PAR

11 10

9

8

7

6

5

4

3

2

1

0

Address

FFFFF3E6H

After reset

0000H

R/W

R

(5) IEBus control data register (CDR)

(a) When master unit

The data of the lower 4 bits is reflected in the data transmitted in the control field.  During master request,

this register must be set in advance before starting communication.

(b) When slave unit

The data received in the control field is written to the lower 4 bits.

When the status transmission flag (STATUS) of the IEBus interrupt status register (ISR) is set, an

interrupt (INTIE2) is issued, and each processing should be performed by software, according to the

value of the lower 4 bits of CDR.

Содержание V850/SB1





























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для V850/SB1

NCR 1651 Quick Reference Manual preview
1651
Бренд: NCR Страницы: 6
Microchip Technology PLECS Quick Start Manual preview
PLECS
Бренд: Microchip Technology Страницы: 37
Echelon Excel 50 Installation Instructions Manual preview
Excel 50
Бренд: Echelon Страницы: 40
S-COM 7K Manual preview
7K
Бренд: S-COM Страницы: 400
Daikin Maverick I Operation Manual preview
Maverick I
Бренд: Daikin Страницы: 48
Daikin MicroTech III Operating Manual preview
MicroTech III
Бренд: Daikin Страницы: 77
Daikin MicroTech III Operation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 32
Daikin MicroTech III Installation And Maintenance Manual preview
MicroTech III
Бренд: Daikin Страницы: 14
Daikin DCS601C51 Hardware Manual preview
DCS601C51
Бренд: Daikin Страницы: 16
Daikin BRC944B2 Quick User Manual preview
BRC944B2
Бренд: Daikin Страницы: 1
S&P RMB Series Manual preview
RMB Series
Бренд: S&P Страницы: 12
S&C Vista SD Programming preview
Vista SD
Бренд: S&C Страницы: 34
S&C Micro-AT Operation preview
Micro-AT
Бренд: S&C Страницы: 32
S&C IntelliCap Plus Installation Manual preview
IntelliCap Plus
Бренд: S&C Страницы: 32
S&P REB 5 Manual preview
REB 5
Бренд: S&P Страницы: 12
S&C PMH Instructions For Operation Manual preview
PMH
Бренд: S&C Страницы: 35
We Care Solar Suitcase Installation Manual preview
Suitcase
Бренд: We Care Solar Страницы: 46
RADEMACHER Troll Comfort Mounting And Operating Instruction preview
Troll Comfort
Бренд: RADEMACHER Страницы: 68

Бренды по названию

Популярные бренды

Загрузить еще бренды