manualshive.com logo in svg

NEC V850/SB1, Руководство пользователя

"NEC V850/SB1" - мощный микроконтроллер, предназначенный для широкого спектра применений. На нашем сайте вы можете бесплатно скачать руководство пользователя для этого устройства. Загрузите его сейчас с manualshive.com.

Поделиться
Скачать
background image

CHAPTER  10    SERIAL  INTERFACE  FUNCTION

User’s Manual  U13850EJ6V0UD

338

(7) Interrupt request signal generator

This circuit controls the generation of interrupt request signals (INTIICn).

An I

2

C interrupt is generated following either of two triggers.

•

Eighth or ninth clock of the serial clock (set by WTIMn bit)

•

Interrupt request generated when a stop condition is detected (set by SPIEn bit)

Remarks 1.

n = 0, 1

2.

WTIMn bit:

Bit 3 of IIC control register n (IICCn)

SPIEn bit:

Bit 4 of IIC control register n (IICCn)

(8) Serial clock controller

In master mode, this circuit generates the clock output via the SCLn pin from a sampling clock (n = 0, 1).

(9) Serial clock wait controller

This circuit controls the wait timing.

(10) ACK output circuit, stop condition detector, start condition detector, and ACK detector

These circuits are used to output and detect various control signals.

(11) Data hold time correction circuit

This circuit generates the hold time for data corresponding to the falling edge of the serial clock.

(12) Start condition generator

This circuit generates a start condition when the STTn bit is set.

However, in the communication reservation disabled status (IICRSVn = 1), when the bus is not released

(IICBSYn = 1), start condition requests are ignored and the STCFn bit is set.

Remark

IICRSVn bit: Bit 0 of IIC flag register n (IICFn)

IICBSYn bit: Bit 6 of IIC flag register n (IICFn)

STCFn bit:

Bit 7 of IIC flag register n (IICFn)

(13) Bus status detector

This circuit detects whether or not the bus is released by detecting start conditions and stop conditions.

However, as the bus status cannot be detected immediately following operation, the initial status is set by the

STCENn bit.

Remark

STCENn bit:  Bit 1 of IIC flag register n (IICFn)

Содержание V850/SB1





























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для V850/SB1

C-TEC 800 Series Installation Instructions preview
800 Series
Бренд: C-TEC Страницы: 2
Lattice LatticeMico8 User Manual preview
LatticeMico8
Бренд: Lattice Страницы: 23
Magnescale LY71 Manual preview
LY71
Бренд: Magnescale Страницы: 3
OMC W150 Installation And Maintenance Instruction preview
W150
Бренд: OMC Страницы: 18
RADEMACHER Troll Comfort Mounting And Operating Instruction preview
Troll Comfort
Бренд: RADEMACHER Страницы: 68
BRT Systems LDSBus LC020101A-F Manual preview
LDSBus LC020101A-F
Бренд: BRT Systems Страницы: 15
GeoVision GV-CS1320 Quick Start Manual preview
GV-CS1320
Бренд: GeoVision Страницы: 21
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Бренд: W.E.ST. Страницы: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Бренд: Ltech Страницы: 4
Motor Guard M-60R Instructions preview
M-60R
Бренд: Motor Guard Страницы: 2
Linak TR-EM-288-SPF Quick Manual preview
TR-EM-288-SPF
Бренд: Linak Страницы: 2
LAB-EL LB-762 Installation Manual preview
LB-762
Бренд: LAB-EL Страницы: 25
Sutter Instrument TRIO MPC-165 Series Operation Manual preview
TRIO MPC-165 Series
Бренд: Sutter Instrument Страницы: 60
AC Tech SCF SERIES Quick Reference Manual preview
SCF SERIES
Бренд: AC Tech Страницы: 2
V-TAC VT-2472 Manual preview
VT-2472
Бренд: V-TAC Страницы: 2
Zander Aachen ZX20T Operating Manual preview
ZX20T
Бренд: Zander Aachen Страницы: 44
Samson 46-7 Mounting And Operating Instructions preview
46-7
Бренд: Samson Страницы: 44
Hansen FROST MASTER Installation Manual preview
FROST MASTER
Бренд: Hansen Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды