Mitsubishi MELSEC-Q QD77MS, Руководство пользователя

Страница: 478 / 976

9 - 45
Chapter 9 Major Positioning Control
Positioning data setting example
[When "4-axis linear interpolation control (ABS linear 4)" is set in positioning data
No. 1 of axis 1]
• Reference axis............. Axis 1
• Interpolation axis.......... Axis 2, Axis3, Axis4 (The required values are also set in
positioning data No. 1 of axis 2, axis 3 and axis 4.)
QD77MS4 setting example QD77MS16 setting example
Axis
Setting item
Axis 1
(reference
axis)
Axis 2
(interpolation
axis)
Axis 3
(interpolation
axis)
Axis 4
(interpolation
axis)
Axis 1
(reference
axis)
Axis 2
(interpolation
axis)
Axis 3
(interpolation
axis)
Axis 4
(interpolation
axis)
Setting details
Da.1
Operation pattern
Positioning
complete
– – –
Positioning
complete
– – –
Set "Positioning
complete" assuming the
next positioning data will
not be executed.
Da.2
Control system
ABS
linear 4
– – –
ABS
linear 4
– – –
Set absolute system 4-
axis linear interpolation
control.
Da.3
Acceleration time
No.
1 – – – 1 – – –
Designate the value set
in "
Pr.25
Acceleration time
1
" as the acceleration
time at start.
Da.4
Deceleration time
No.
0 – – – 0 – – –
Designate the value set
in "
Pr.10
Deceleration time
0
" as the deceleration
time at deceleration.
Da.5
Axis to be
interpolated
QD77MS4
– – – –
Setting not required
(setting value is ignored).
When axis 1 is used as a
reference axis, the
interpolation axes are
axes 2, 3 and 4.
Da.6
Positioning address/
movement amount 4000.0
μ
m
8000.0
μ
m
4000.0
μ
m
3000.0
μ
m
4000.0
μ
m
8000.0
μ
m
4000.0
μ
m
3000.0
μ
m
Set the end point
address. (Assuming
"mm" is set in "
Pr.1
Unit
setting
".)
Da.7
Arc address – – – – – – – –
Setting not required
(setting value is ignored).
Da.8
Command speed
6000.00
mm/min
– – –
6000.00
mm/min
– – –
Set the speed during
movement to the end
point address.
Da.9
Dwell time 500ms – – – 500ms – – –
Set the time the machine
dwells after the
positioning stop
(command stop) to the
output of the positioning
complete signal.
Da.10
M code 10 – – – 10 – – –
Set this when other sub
operation commands are
issued in combination
with the No. 1 positioning
data.
Da.20
Axis to be
interpolated No.1
QD77MS16
Axis 2 – – –
Da.21
Axis to be
interpolated No.2
QD77MS16
Axis 3 – – –
A
xi
s 1 P
osi
tioni
ng data N
o. 1
Da.22
Axis to be
interpolated No.3
QD77MS16
Axis 4 – – –
Set the axis to be
interpolated.
If the self-axis is set, an
error will occur.
(Note): Refer to Section 5.3 "List of positioning data" for information on the setting details.