manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Продукт Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN - передовое устройство для автоматизации систем. У вас есть возможность загрузить бесплатное руководство по эксплуатации на manualshive.com. Получите доступ к детальной информации в этом руководстве для оптимального использования продукта.

Поделиться
Скачать
background image

APPX

Appendix 7  Processing Time

307

A

Multicast mode (100Mbps)

■

Calculation formula

Communication cycle interval [ns] = 

c

 + 

p

 + 

sc

 + 

sp

. Round up values of 

c

, 

p

, 

sc

, and 

sp

 that are less than 1

s.

Cyclic transmission time [ns] = 

c

 + 

sc

 •

c

: This value varies depending on whether a CC-Link IE TSN Class A slave station with the basic cycle or normal speed 

cycle exists or not.

*1 The symbols in the table are as follows.

A1, B1, C1: Main module calculation formula
A2, B2, C2: Extension module calculation formula

For the maximum response time for time-managed polling for the slave stations, refer to the user's manual for 
the slave station used.

 •

sc

: The calculation formula is as follows.

Cyclic processing time [ns] = 

p

 + 

sp

 or 340000, whichever is larger.

 •

p

: p1+p2+p3+kp+kum

 •

sc

 is calculated by p4.

■

Variable

For each variable to be used, round it up to one decimal point before assigning to the calculation formula.

Item

Calculation formula

When a CC-Link IE TSN Class A slave station with the basic cycle or normal 
speed cycle does not exist

No.1 + No.4

When a CC-Link IE TSN Class A slave station with the basic cycle or normal 
speed cycle exists

No.1+No.4+No.5

No.

Calculation formula

*1

1

A1 + A2 + (the value obtained by 
the calculation formula in No.2 or 
No.3, whichever is larger)

A1: {(42

(n1r+n1l))+(16

(n2r+n2l))+(ndmr+ndml)}

80+(Sn-1)

5150+14000+nh+nrp

A2: {(42

en1r)+(16

en2r)+endmr}

80

2

B1+B2

B1:  {(42

n3)+(20

n4)+nds}

80+14000+nh

B2: {(42

en3)+(20

en4)+ends}

80

3

C1+C2

C1: {(42

n5)+(20

n6)+ndl}

80+(Sn-1)

5150+14000+nh

C2: {(42

en5)+(20

en6)+endl}

80

4

D

n7

D: (Sn-1)

5150+187440

5

The largest value among the maximum response times during the time-managed polling of the CC-Link IE TSN Class A slave stations set in the basic 
cycle or medium speed cycle

Calculation formula

{(42 

 (sn1r+sn1l)) + (16 

 (sn2r+sn2l)) + (sndmr+sndml)} 

 80

Name of variable

Description

n1r

(ndmr + (16 

 n2r))/1488 or Rn, whichever is larger

n1l

Round up the calculated value to the nearest integer of (ndml+(16 

 n2l))/1488

sn1r

(sndmr + (16 

 sn2r))/1488 or SRn, whichever is larger

sn1l

Round up the calculated value to the nearest integer of (sndml+(16 

 sn2l))/1488

n2r

Rn

(RYrb+RWwrb)

RYrb: Value of (Total number of points of "RY setting" set in the remote station (main modules))/(11776 

 Rn) rounded up to the 

nearest integer
RWwrb: Value of (Total number of points of "RWw setting" set in the remote station (main modules))/(736 

 Rn) rounded up to the 

nearest integer

n2l

RYlb+RWwlb+LBmb+LWmb+1
RYlb: Value of (Total number of points of "RY setting"

*2

)/11776 rounded up to the nearest integer

RWwlb: Value of (Total number of points of "RWw setting"

*2

)/736 rounded up to the nearest integer

LBmb: Value of (Number of points of "LB setting" set in the master station)/11776 rounded up to the nearest integer
LWmb: Value of (Number of points of "LW setting" set in the master station)/736 rounded up to the nearest integer

sn2r

SRn 

 SRYrb

SRYrb: The number of connections in the remote stations of "Safety Communication Setting" in "Basic Settings" set in the master 
station/(18.4 

 SRn) rounded up to the nearest integer

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

UE 120 Series Installation And Maintenance Instructions preview
120 Series
Бренд: UE Страницы: 4
XBOX 360 Manual preview
360
Бренд: XBOX Страницы: 7
CAME Z Series Instruction Manual preview
Z Series
Бренд: CAME Страницы: 12
CAME Z Series Technical Documentation Manual preview
Z Series
Бренд: CAME Страницы: 16
Ultrak KEGS5000 User Manual preview
KEGS5000
Бренд: Ultrak Страницы: 41
Zander Aachen ZX Series Quick Start Manual preview
ZX Series
Бренд: Zander Aachen Страницы: 10
Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Бренд: Galcon Страницы: 32
Caen V793 Technical Information Manual preview
V793
Бренд: Caen Страницы: 20
Gardena Master Operator'S Manual preview
Master
Бренд: Gardena Страницы: 18
Danfoss VLT Micro Drive FC 51 Series Quick Manual preview
VLT Micro Drive FC 51 Series
Бренд: Danfoss Страницы: 23
GAC ESD-5550 Series Technical Information preview
ESD-5550 Series
Бренд: GAC Страницы: 12
Madas M16/RMO NA/NC Installation Instructions Manual preview
M16/RMO NA/NC
Бренд: Madas Страницы: 6
Madas EVP/NC Manual preview
EVP/NC
Бренд: Madas Страницы: 11
R82 Cricket User Guidance preview
Cricket
Бренд: R82 Страницы: 89
Rabbit RCM2000 Getting Started Manual preview
RCM2000
Бренд: Rabbit Страницы: 38
R82 Serval Mounting Instruction preview
Serval
Бренд: R82 Страницы: 8
RadioMaster MT12 Instruction Manual preview
MT12
Бренд: RadioMaster Страницы: 49
X10 SUPERREMOTE UR19A Addendum preview
SUPERREMOTE UR19A
Бренд: X10 Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды