manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Продукт Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN - передовое устройство для автоматизации систем. У вас есть возможность загрузить бесплатное руководство по эксплуатации на manualshive.com. Получите доступ к детальной информации в этом руководстве для оптимального использования продукта.

Поделиться
Скачать
background image

4  TROUBLESHOOTING

4.5  List of Error Codes

229

4

D653H

Parameter error (transient transmission 
group setting)

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the transient transmission 

group setting in the setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D654H

Parameter error (dynamic routing setting)

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting the dynamic routing setting 

in the setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D655H

Network addresses of the master station and 
slave stations are incorrect.

Correct the IP address setting of the master station or slave stations.

D656H

Parameter error (CANopen communications)

Update the version of the engineering tool that supports the CANopen 
communication function, then write parameters to the CPU module again.

D657H

Parameter error (station sub-ID)

• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D658H

Parameter error (multidrop number)

• Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D659H

Parameter error (CANopen communication)

The CANopen communication function cannot be used. Clear the PDO 
mapping setting in the engineering tool, and write the parameter to the CPU 
module again.

D65AH

Parameter error (maximum number of 
connectable stations)

• Parameters are set over the maximum number of connectable stations. 

Correct the parameter so that the number of slave stations is 120 or less, 
then write parameters to the CPU module again. Note that a PDO-
mapped extension module (for example, a multi-axis servo amplifier) to 
which a station number is not set is counted as one station.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D65BH

Parameter error (CC-Link IE TSN Class 
setting)

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting "CC-Link IE TSN Class 

Setting" in the setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D65CH

Parameter error (TSN hub setting)

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting "TSN HUB Setting" in the 

setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D65DH

Parameter error (multiple period setting)

• Write the network parameter to the CPU module again.
• Execute the instruction again after correcting "Multiple Period Setting" in 

the setting data.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D840H

Number of transient requests exceeded the 
upper limit of simultaneously processable 
requests.

• Execute the instruction again after pausing the transient transmission 

temporarily.

• Execute the instruction again after lower the transient transmission usage 

frequency.

D841H

The request data size of memory read/write 
command is out of range.

Execute the instruction again after correcting the read or write size 
specification at the transient request source.

D842H

• Routing information to the destination 

network number is not registered.

• In transient transmission, the number of 

relays to other networks exceeded seven.

• The communication path is being updated.

• Execute the instruction again after correcting the target network number 

at the transient request source.

• Execute the instruction again after correcting the communication path 

from the transient request source to the destination.

• When the dynamic routing is not used, or the module of the series other 

than MELSEC iQ-R is included, retry the operation after correcting the 
routing setting.

• Change the system configuration so that the number of relay stations is 

seven or less.

• Transient transmission cannot be performed while the communication 

path is being updated. Retry the operation.

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

Ubisys J1 Manual preview
J1
Бренд: Ubisys Страницы: 2
DayTronic 3700 Series Instruction Manual preview
3700 Series
Бренд: DayTronic Страницы: 22
DayTronic System 10 User Manual Book preview
System 10
Бренд: DayTronic Страницы: 414
YOKOGAWA UT35A-L User Manual preview
UT35A-L
Бренд: YOKOGAWA Страницы: 150
YOODA NANO Series Quick Start Manual preview
NANO Series
Бренд: YOODA Страницы: 3
YMGI 584 Series User Manual preview
584 Series
Бренд: YMGI Страницы: 8
Vag CEREX 300-L Operation & Maintenance Instructions Manual preview
CEREX 300-L
Бренд: Vag Страницы: 15
AAF MicroTech II UV05 Operation & Maintenance Manual preview
MicroTech II UV05
Бренд: AAF Страницы: 50
S&P PDS CONTROL Series Manual preview
PDS CONTROL Series
Бренд: S&P Страницы: 32
HomeMatic HM-RC-12 Operating Manual preview
HM-RC-12
Бренд: HomeMatic Страницы: 36
Kohler DTV+ Installation And Care Manual preview
DTV+
Бренд: Kohler Страницы: 48
Notifier AUTOPULSE IQ-318 Manual preview
AUTOPULSE IQ-318
Бренд: Notifier Страницы: 62
G&D PersonalWorkplace Pro Video Installation Manual preview
PersonalWorkplace Pro Video
Бренд: G&D Страницы: 56
Beninca DA.93AM Operating Instructions Manual preview
DA.93AM
Бренд: Beninca Страницы: 16
Graco GIM-0050E Instructions Manual preview
GIM-0050E
Бренд: Graco Страницы: 41
Woodward 723PLUS Original Instructions Manual preview
723PLUS
Бренд: Woodward Страницы: 118
Frico IHMC6-3 Original Instructions Manual preview
IHMC6-3
Бренд: Frico Страницы: 8
ASROCK iEP-5000G Series Quick Installation Manual preview
iEP-5000G Series
Бренд: ASROCK Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды