manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 291

APPX

Appendix 7  Processing Time

289

A

Cyclic transmission delay time

This section describes how to calculate the following cyclic transmission delay times.
 • The time between the transmission source CPU module device turning on or off and the transmission destination CPU 

module device turning on or off

 • The time between data setting in the transmission source CPU module device and the data being stored in the transmission 

destination CPU module device

In "Basic Settings" of the master station, when "Communication Period Setting" of the communication destination in "Network 
Configuration Settings" is set to an option other than "Basic Period", multiply the LS (communication cycle intervals) by the 
multiplier corresponding to the set option, which is specified in "Multiple Period Setting" under "Communication Period 
Setting".
At this time, the multiple is as follows, depending on "Communication Period Setting" under "Basic Settings" and "CC-Link IE 
TSN Class" under "Network Configuration Settings".
 • For "CC-Link IE TSN Class B": The multiple specified in "Multiple Period Setting" in "Communication Period Setting" under 

"Basic Settings"

 • When "CC-Link IE TSN Class A" and "Communication Period Setting" are "Normal-Speed": The multiple specified in 

"Multiple Period Setting" in "Communication Period Setting" under "Basic Settings"

 • When "CC-Link IE TSN Class A" and "Communication Period Setting" are "Low-Speed": The multiple 

 n specified in 

"Multiple Period Setting" in "Communication Period Setting" under "Basic Settings"

n can be checked with 'Slave station cyclic transmission information' (Un\G1294304).
Stations with "CC-Link IE TSN Class A" where "Communication Period Setting" is set to "Low-Speed" are grouped by the 
sizes of cyclic data sent from the master station to a slave station or cyclic data which the master station receives from a slave 
station. The number n is determined by the number of the groups.

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды