Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 142

Страница: 142 / 330

140

3 PROGRAMMING
3.2 Communication Example with CC-Link IE TSN Class A Remote Station

Set the refresh settings as follows.

[Navigation window]



[Parameter]



[Module Information]



[RJ71GN11-T2]



[Basic Settings]



[Refresh Settings]



[Detailed Setting]

Set the items in "Application Settings" as follows.

[Navigation window]



[Parameter]



[Module Information]



[RJ71GN11-T2]



[Application Settings]

Click the [Apply] button.

Write the set parameters to the CPU module on the local station. Then, reset the CPU module or power off and on the
system.

[Online]



[Write to PLC]

In the program example, default values are used for parameters that are not shown above. For the
parameters, refer to the following.



Page 94 PARAMETER SETTINGS

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Результаты поиска

Содержание MELSEC iQ-R CC-Link IE TSN

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Результаты поиска

Содержание MELSEC iQ-R CC-Link IE TSN

Отзывы:

Бренды по названию

Популярные бренды