manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Продукт Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN - передовое устройство для автоматизации систем. У вас есть возможность загрузить бесплатное руководство по эксплуатации на manualshive.com. Получите доступ к детальной информации в этом руководстве для оптимального использования продукта.

Поделиться
Скачать
background image

220

4  TROUBLESHOOTING
4.5  List of Error Codes

D203H

The read data or write address of the 
transient transmission is incorrect.

Execute the instruction again after correcting the read data or write address 
at the transient request source.

D205H

The target station number of transient 
transmission is incorrect.

Execute the instruction again after correcting the target station number at 
the transient request source.

D20AH

The target station number of transient 
transmission is incorrect.

Execute the instruction again after correcting the target station number at 
the transient request source.

D20BH

There was no master station when the 
specified master station was specified for 
transient transmission.

Execute the instruction again after correcting the target station number at 
the transient request source.

D20CH

There was no master station when the 
current master station was specified for 
transient transmission.

Execute the instruction again after correcting the target station number at 
the transient request source.

D20DH

Transmission completion wait timeout has 
occurred in transient data transmission.

• Check the network status using the CC-Link IE TSN/CC-Link IE Field 

diagnostics of the engineering tool, and take action.

• When the own station, target station, or relay station detected an error, 

identify the cause of the error and take action.

• Execute the instruction again after lower the transient transmission usage 

frequency.

• Check if the switching hub and the Ethernet cables at the request source 

are connected properly.

D20EH

The header information of transient 
transmission is incorrect.

Execute the instruction again after correcting the header information at the 
transient request source, and retry the operation.

D20FH

In transient transmission, the command 
which cannot be requested to all or a group 
of stations was executed with all stations 
specification or group specification.

Execute the instruction again after checking that the command can be 
requested to all or a group of stations at the transient request source.

D211H

Transient transmission was performed when 
the station number/IP address of the own 
station had not been set yet.

Set the station number/IP address using the UINI instruction, and perform 
transient transmission again.

D213H

• The command of transient transmission is 

incorrect.

• The CC-Link IE TSN/CC-Link IE Field 

diagnostics was used for the network to 
which the relay receiving station belongs.

• The module at the connection destination 

does not support this function.

• Execute the instruction again after correcting the request command at the 

transient request source, and retry the operation.

• Review the connection destination so that the CC-Link IE TSN/CC-Link IE 

Field diagnostics is used for the network to which the relay sending station 
belongs.

• Check the manual for the module at the connection destination and check 

the status of support for this function. If not supported, update the 
firmware version to the one that supports this function.

D214H

The data length of transient transmission is 
incorrect.

Execute the instruction again after correcting the data length at the transient 
request source, and retry the operation.

D239H

SLMP transmission failed.

• Retry the operation after a while.
• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

D240H

The network number specification of the 
dedicated instruction is incorrect.

• Execute the instruction again after correcting the network number at the 

request source of the dedicated instruction.

• If the request source is on another network, check if "Routing Settings" of 

CPU parameters are set correctly, and take action.

D241H

The target station number of the dedicated 
instruction is incorrect.

• Execute the instruction again after correcting the target station number at 

the request source of the dedicated instruction.

• If the request source is on another network, check if "Routing Settings" of 

CPU parameters are set correctly, and take action.

D242H

The command code of the dedicated 
instruction is incorrect.

• Execute the instruction again after correcting the command code at the 

request source of the dedicated instruction.

• If the request source is on another network, check if "Routing Settings" of 

CPU parameters are set correctly, and take action.

D243H

The channel specified in the dedicated 
instruction is incorrect.

• Execute the instruction again after correcting the used channel within the 

allowable range at the request source of the dedicated instruction.

• If the request source is on another network, check if "Routing Settings" of 

CPU parameters are set correctly, and take action.

D244H

The transient data is incorrect.

• Execute the instruction again after correcting the transient data at the 

transient request source.

• If the error occurs again even after taking the above, please consult your 

local Mitsubishi representative.

Error 
code

Error definition and causes

Action

Detailed 
information 1

Detailed 
information 2

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

ABB Relion REC670 Product Manual preview
Relion REC670
Бренд: ABB Страницы: 138
ABB Relion REC670 Operator'S Manual preview
Relion REC670
Бренд: ABB Страницы: 116
ABB Relion 615 series Operation Manual preview
Relion 615 series
Бренд: ABB Страницы: 136
Rayrun BR11 Quick Installation Manual preview
BR11
Бренд: Rayrun Страницы: 2
IDenticard 9000 Series Converting Instructions preview
9000 Series
Бренд: IDenticard Страницы: 2
3Ware 9000 Series Specification preview
9000 Series
Бренд: 3Ware Страницы: 2
Jafar 2112 Operation And Maintenance Manual preview
2112
Бренд: Jafar Страницы: 9
Nelsen Corporation C Series Programming Manual preview
C Series
Бренд: Nelsen Corporation Страницы: 16
National Instruments C Series Getting Started preview
C Series
Бренд: National Instruments Страницы: 34
Ubisys J1 Manual preview
J1
Бренд: Ubisys Страницы: 2
IBM 3746-900 Installation Manual preview
3746-900
Бренд: IBM Страницы: 276
IBM 4769 Installation Manual preview
4769
Бренд: IBM Страницы: 32
IBM 3745 Series Connection And Integration Manual preview
3745 Series
Бренд: IBM Страницы: 157
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Бренд: Zamel Страницы: 2
Yamaha DCP4S-US Owner'S Manual preview
DCP4S-US
Бренд: Yamaha Страницы: 2
WAGNER 2K COMFORT Original Operating Manual preview
2K COMFORT
Бренд: WAGNER Страницы: 128
YASKAWA CIMR-ZU Series Programming Manual preview
CIMR-ZU Series
Бренд: YASKAWA Страницы: 340
Alde 3010 413 Instructions For Use And Assembly preview
3010 413
Бренд: Alde Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды