manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 104

102

2  PARAMETER SETTINGS
2.3  Basic Settings

Network Topology

Select the network topology type according to the actual network configuration.

Network synchronous communication cannot be performed when "Network Topology" is set to "Ring". Select 
"Line/Star".

Communication Period Setting

Set the basic cycle setting and multiple cycle setting.
 • Basic cycle setting requires calculation of the communication cycle interval and cyclic transmission time. (

 Page 293 

Communication cycle intervals)

 • Multiple cycle setting is used when communication cycles coexist. (

 Page 42 Communication cycles coexistence)

*1 This communication cycle can be used for the firmware version "04" or later.
*2 The setting range of the firmware version "03" or earlier is from 125.00

s to 4000.00

s.

*3 The setting range of the firmware version "03" or earlier is from 5.00

s to 3966.00

s.

*4 The setting range of the firmware version "03" or earlier is from 14.00

s to 3975.00

s.

*5 To use the CC-Link IE TSN network synchronous communication function, set the same value as the value set in "Fixed Scan Interval 

Setting" of "Fixed Scan Interval Setting of Inter-module Synchronization" under "Inter-module Synchronization Setting" in the "Inter-
module Synchronization Setting" tab of "System Parameter".

*6 This communication cycle can be used for the firmware version "14" or later.

Item

Description

Setting range

Network 
Topology

Select the network topology type according to the actual 
network configuration.
To use the loopback function, select "Ring". (

 Page 69 

Loopback Function)

• Line/Star
• Ring

(Default: Line/Star)

Item

Description

Setting range

Basic Period 
Setting

Setting in Units of 1

s

Select whether to set the basic cycle in increments of 1

s.

• Set
• Not set

(Default: Not set)

Communication Period Interval Setting 
(Do Not Set it in Units of 1

s)

*5

Select the setting range of the communication cycle interval.

• 125.00

s

• 250.00

s

• 500.00

s

• 1000.00

s

• 2000.00

s

• 4000.00

s

• 8000.00

s

*1

(Default: 1000.00

s)

Communication Period Interval Setting 
(Set it in Units of 1

s)

*5

Enter a value of the communication cycle interval.

125.00

s to 10000.00

s (in 

increments of 1

s)

*2

(Default: 1000.00

s)

System Reservation Time

Necessary time for the system to guarantee the 
communication cycle interval.
When "Communication Speed" of the master station is set to 
100Mbps, select 200

s.

• 20.00

s

• 200.00

s

(Default: 20.00

s)

Cyclic Transmission Time

Set the time to be allocated to cyclic transmission in 
communication cycle intervals.

5.00

s to 9966.00

s (in 

increments of 1

s)

*3

(Default: 500.00

s)

Transient Transmission Time

The value of "Communication Period Interval Setting" minus 
"Cyclic Transmission Time" and "System Reservation Time" is 
displayed.

14.00

s to 9975.00

s (in 

increments of 1

s)

*4

(Default: 480.00

s)

Multiple Cycle 
Setting

Normal-Speed

Select the "Normal-Speed" cycle for a basic cycle.
Setting is not required and can be left as "

4".

(Default: 

4)

Low-Speed

Select the "Low-Speed" cycle for a basic cycle.

•

16

•

32

*6

•

64

*6

•

128

*6

(Default: 

16)

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды