manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Продукт Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN - передовое устройство для автоматизации систем. У вас есть возможность загрузить бесплатное руководство по эксплуатации на manualshive.com. Получите доступ к детальной информации в этом руководстве для оптимального использования продукта.

Поделиться
Скачать
background image

4  TROUBLESHOOTING

4.4  Troubleshooting by Symptom

187

4

If the above actions do not solve the problem, perform the module communication test to check for hardware failure. (

 

Page 168 Module Communication Test)

When "Connection 
Device Information" 
under "Basic Settings" 
of the master station is 
set to "Mixture of CC-
Link IE TSN Class B/A 
or CC-Link IE TSN 
Class A Only"

■

For firmware version "14"

Is a CC-Link IE TSN Class A device that supports 
the CANopen profile with the protocol version 2.0 
connected?

Update the firmware version of the master station to "15" or later.

If the stations are connected in a line topology, do "Communication Speed" for 
the stations match one another?

Correct "Communication Speed" under "Application Settings" for the stations 
so that the communication speeds match one another.

Is there any reason why cyclic transmission cannot be performed on the slave 
station side?

• Check if an error has occurred on the slave station.
• Check if the slave station settings and parameters are correct.
• Refer to the manual of the slave station for troubleshooting.

Is the event code 00C44 registered in the event history?

Match the communication speed of the master station to the communication 
speed of the station for which the slave station parameter automatic setting is 
to be configured.

When "Network 
Topology" under "Basic 
Settings" of the master 
station is set to "Ring"

Is a switching hub used?

Disconnect the switching hub.

Is a device not supporting ring topology 
connected?

Disconnect the device not supporting ring topology, and connect a device 
supporting ring topology.

Is the communication speed of the master station 
the same as the communication speed of slave 
station?

Ensure that the communication speed of the master station and the 
communication speed of slave station match.

■

For firmware version "13" or earlier

Is a device not set in "Network Configuration 
Settings" of the master station connected?

Disconnect the device not set in "Network Configuration Settings" of the 
master station.

Is the minimum value for communication cycle interval set to both 
"Communication Period Interval Setting" and "Cyclic Transmission Time" in 
"Communication Period Setting" under "Basic Settings" of the module 
parameter?

Set "Cyclic Transmission Time" to a value obtained by the following formula: 
Minimum value of cyclic transmission time + Greatest value among the two 
values shown below.

• 10% of the calculated minimum cyclic transmission time
• When the communication speed of the master station is set to 1Gbps: 

Number of slave stations 

 2

s

• When the communication speed of the master station is set to 100Mbps: 

Number of slave stations 

 20

s

Is the minimum value for cyclic transmission time set to "Cyclic Transmission 
Time" in "Communication Period Setting" under "Basic Settings" of the module 
parameter?

In multicast mode, has an external device sent a frame to a station before data 
link establishment of all stations?

Ensure that the external device will not send a frame before data link 
establishment of all stations, then reset the master station.

When "Communication Speed" of the master station is 1Gbps, has the cyclic 
data size exceeded 2K bytes in total for all slave stations on the CC-Link IE 
TSN Class B device side with the communication speed 100Mbps at the 
boundary between CC-Link IE TSN Class B (except for the master station) 
and CC-Link IE TSN Class A?

• Restrict the number of the connected stations so that the cyclic data size of 

the devices with communication speed of 100Mbps does not exceed 2K 
bytes in total.

• Connect the device with communication speed of 100Mbps to the master 

station.

■

For firmware version "14"

When the communication speed of the master station and the slave station of 
the CC-Link IE TSN Class A is 1Gbps, is the "Communication Period Setting" 
of the slave station of the CC-Link IE TSN Class A set to "Basic Period" or 
"Normal-Speed"?

• Update the firmware version of the master station to "15" or later.
• Set the value set for "Communication Period Interval Setting" and "Cyclic 

Transmission Time" in "Communication Period Setting" under "Basic 
Settings" to greater than or equal to the calculation value of the calculation 
formula. (

Page 293 Communication cycle intervals)

Check item

Action

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

Wavelink Avalanche User Manual preview
Avalanche
Бренд: Wavelink Страницы: 69
janitza 800-CT8-A User Manual And Technical Data preview
800-CT8-A
Бренд: janitza Страницы: 58
U.S. Divers Impulse Service & Repair Manual preview
Impulse
Бренд: U.S. Divers Страницы: 22
G-Force UNDER CONTROL CP-30A PILOT User Manual preview
UNDER CONTROL CP-30A PILOT
Бренд: G-Force Страницы: 2
Paser AFRTX/4T Quick Start Manual preview
AFRTX/4T
Бренд: Paser Страницы: 2
Computer Automation Technology CAT-250 Manual preview
CAT-250
Бренд: Computer Automation Technology Страницы: 55
Audioaccess PX-700 Manual preview
PX-700
Бренд: Audioaccess Страницы: 2
Mitsubishi AL-ASI-BD Hardware Manual preview
AL-ASI-BD
Бренд: Mitsubishi Страницы: 16
SOMFY Situo 1 RTS Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 4
Tech 21 MIDI MONGOOSE Owner'S Manual preview
MIDI MONGOOSE
Бренд: Tech 21 Страницы: 2
National Instruments SCXI-1120/D Calibration Procedure preview
SCXI-1120/D
Бренд: National Instruments Страницы: 19
LCT HQ-TJ-901 Operation Manual preview
HQ-TJ-901
Бренд: LCT Страницы: 5
Modine Manufacturing Airedale Sentinel Quick Start Manual preview
Airedale Sentinel
Бренд: Modine Manufacturing Страницы: 2
OGI TotalArc BMS 460346 SOLAR POWER Operator'S Manual preview
TotalArc BMS 460346 SOLAR POWER
Бренд: OGI Страницы: 28
DAYLIFF SUNVERTER B Installation & Operating Manual preview
SUNVERTER B
Бренд: DAYLIFF Страницы: 40
Danfoss WVS 32 Installation Manual preview
WVS 32
Бренд: Danfoss Страницы: 4
CALEFFI Z-one ZVR103 Manual preview
Z-one ZVR103
Бренд: CALEFFI Страницы: 56
3M Touch Screen Controller RX142 Reference Manual preview
Touch Screen Controller RX142
Бренд: 3M Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды