manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 109

2  PARAMETER SETTINGS

2.3  Basic Settings

107

2

Communication Period Interval (Minimum 
value)

The communication cycle intervals that are calculated by the 
number of slave stations and the number of points of link devices 
by using the values set for standard communications and safety 
communications are displayed. Use the displayed value as a 
guide.

*1

The displayed value differs depending on "TSN HUB Setting" of 
"Connection Device Information" under "Basic Settings" even 
when the number of slave stations and link device points are the 
same. For details, refer to the following.

Page 293 Communication cycle intervals

The displayed value can be used for "Communication Period 
Interval Setting" in "Communication Period Setting" under "Basic 
Settings" of the module parameter.
If cyclic transmission is not performed by configuring the setting 
with the displayed value, set a value obtained by adding 10% as 
follows.
Calculation formula: B+A

0.1

A: Cyclic transmission time (minimum value)
B: Communication cycle interval (minimum value)

When the communication speed of the master station is 1Gbps 
in unicast mode or multicast mode with version 1.085P or earlier 
of the engineering tool (if a CC-Link IE TSN Class A slave station 
with the basic cycle or normal speed cycle exists), the interval 
cannot be checked. Check it with 'Communication cycle interval 
(calculation value)' (SW0072).

Page 274 List of link special register (SW)

Setting Method

Right-click in the "Safety Communication Setting" window and 
select an assignment method in "Safety Data Transfer Device 
Setting".

• Start/End: Enter the start and end numbers of safety devices.
• Points/Start: Enter the points and start numbers of safety 

devices.

• Start/End
• Points/Start

(Default: Start/End)

No.

Safety connection number for distinguishing settings for each 
safety connection.

1 to 120

*2

Communication Destination

Set a network of the communication destination.

Local Network
(Default: empty)

Network 
Configuration

Network No.

The network number of the communication destination is 
displayed.

Station No.

When the own station is the master station: The station number 
of communication destination selected in the "Select the target 
module for the Safety Communication Setting" window is 
displayed.

IP Address

When the own station is the master station: The IP address of 
communication destination selected in the "Select the target 
module for the Safety Communication Setting" window is 
displayed.

0.0.0.1 to 223.255.255.254
(Default: empty)

Station Type

When the own station is the master station: The station type of 
the communication destination selected in the "Select the target 
module for the Safety Communication Setting" window is 
displayed.

Configured Module

Model Name

When the own station is the master station: The module model 
name of the communication destination selected in the "Select 
the target module for the Safety Communication Setting" window 
is displayed. (Only slave station other than the local station)

Communication 
Destination

When the communication destination is a local station: Set the 
CPU model name of communication destination.

• R08SFCPU
• R16SFCPU
• R32SFCPU
• R120SFCPU
• R16NCCPU
• CR800-R

(Default: empty)

PLC No.

When the own station is the master station: Set the CPU number 
of the communication destination when the CPU module of the 
communication destination is set to CPU module other than the 
Safety CPU.

2 to 4
(Default: empty)

Item

Description

Setting range

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды