Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 330

background image

74

1 FUNCTIONS
1.5 RAS

IP address duplication detection

If one network has stations with the same IP address, an overlap is detected.
• When adding a slave station, if a station with the same IP address already exists, IP address duplication detection (error

code: 2160H) is detected in a station to be added and data link cannot be performed. Other stations continue data link.

Precautions

When adding a slave station, which has already been connected (linked up) with a TSN hub and the TSN hub is added to the
network, an overlapping IP address is not detected in a station to be added. If IP address duplication detection (error code:
1802H) is detected in the master station, disconnect the relevant slave station from the network. Otherwise, multiple stations
with the same IP address will exist on the same network, possibly leading to transient transmission being sent to an
unintended station.
• If the startup processing of cyclic transmission is executed by powering off and on the master station, when a station with

the same IP address is in the network, Slave IP address duplication (error code: 3021H) is detected in the master station
and data link cannot be performed.

• During cyclic transmission, an overlapping IP address is regularly checked in the master station. When there are

overlapping IP addresses, IP address duplication detection (error code: 1802H) is detected in the master station and cyclic
transmission cannot be performed with the relevant slave station. Other stations continue data link.

• An overlapping IP address between an Ethernet device and a CC-Link IE TSN device, and an overlapping

IP address between Ethernet devices are not detected at cyclic transmission startup of the master station.

• Station number duplication is not detected.

Methods of recovery from an overlapping IP address

If IP address duplication detection (error code: 1802H) or Slave IP address duplication (error code: 3021H) is detected on the
master station, change the IP address of the relevant station, and power off and on or reset the master station.

192.163.3.0

192.163.3.1

192.163.3.2

192.163.3.1

192.163.3.0

192.163.3.1

192.163.3.2

192.163.3.1

«
...
74
75
76
77
78
...
»

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

ESSENSSE NEO COMFORT

Бренд: 2VV Страницы: 21

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: rada Страницы: 16

Бренд: NAPCO Страницы: 48

Magnum Alert 2600

Бренд: NAPCO Страницы: 68

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 25

Бренд: U-Prox Страницы: 2

Бренд: Vanderbilt Страницы: 2

Бренд: C&C Страницы: 17

Бренд: Valco baby Страницы: 8

Бренд: Tenpilot Страницы: 2

Бренд: Tamiya Страницы: 5

Бренд: Dickey-John Страницы: 109

by-me Eikon 20526

Бренд: Vimar Страницы: 6

Бренд: Daikin Страницы: 32

Бренд: Ebyte Страницы: 20

EG-PWC-PSWRC-01

Бренд: Energenie Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды