Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 330

background image

1 FUNCTIONS

1.6 CC-Link IE TSN Network Synchronous Communication Function

79

1

Compatible device

The following table shows the devices that can be synchronized by the CC-Link IE TSN network synchronous communication
function.



: Synchronizable,



: Not synchronizable

■

Setting for a station not synchronizable

• When the network synchronous communication setting is set for a slave station that is not synchronizable, Initialization

failure (parameter mismatch between master and slave stations) (event code: 00C71) is displayed in the event history in
the master station. (Network synchronous communication and cyclic transmission with other slave stations are continued.)

• In the local station for which "Network Synchronous Communication" in "Network Configuration Settings" under "Basic

Settings" of the master station is set to "Synchronous", if "Select Inter-module Synchronization Target Module" in "System
Parameter" on the local station side is set to "Asynchronous", Inter-module synchronization target mismatch (error code:
3601H) occurs.

Support of the CC-Link IE
TSN Network
synchronous
communication function

CC-Link IE TSN Class

Communication speed

Communication cycle
setting

Synchronizability

Not supported









Supported

CC-Link IE TSN Class A
device







CC-Link IE TSN Class B
device

1Gbps

Basic Period



Normal-Speed



Low-Speed



100Mbps

Basic Period



Normal-Speed



Low-Speed



«
...
79
80
81
82
83
...
»

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

Бренд: K&K Страницы: 6

Бренд: FAAC Страницы: 14

Бренд: Rabbit Страницы: 38

Бренд: R82 Страницы: 8

Бренд: UniPOS Страницы: 51

Бренд: Unipulse Страницы: 126

Бренд: YachtSafe Страницы: 3

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 26

Wireless Blade FX Controller for Wii

Бренд: Datel Страницы: 2

Бренд: Fox Страницы: 5

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

Бренд: DAQ Страницы: 63

Бренд: FuzzDog Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды