Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 330

background image

114

2 PARAMETER SETTINGS
2.4 Application Settings

Link devices set for "Source" can be overlapped. Doing so will allow transfer of the same link devices to
multiple network modules.

Precautions

■

Modules that can support interlink transmission

• RJ71GN11-T2 (master station)
• CC-Link IE Controller Network-equipped module (control station, normal station)
• CC-Link IE Field Network-equipped module (master station and submaster station)
• RJ71LP21-25 (control station and normal station)

■

Transfer destination link device setting

Do not use link devices set for link refresh range as a transfer destination. If doing so, transfer destination link devices will be
overwritten by link refresh. To use transfer destination link device data in the CPU module, set the transfer source link device
as the link refresh range.

RWr/LW
LW/RWw

Source

Enter the link device range of the transfer source and destination modules. Up to 64 interlink
transmission ranges can be set. RWr and RWw points can be assigned in increments of 4.

RWr: 0H to 1FFFH
RWw: 0H to 1FFFH
(Default: empty)

Destination

Item

Description

Setting range

RWr

LW

LW

RWr

LW

RWw

RWw

LW

LW

RWr

RWw

LW

No.1

No.2

No.64

No.1

No.2

No.64

·

·

·

·

·

·

Transfer
source

Link refresh
range 1

Link refresh
range 2

CPU module

Network
module 1

Network
module 2

«
...
114
115
116
117
118
...
»

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

Бренд: QCON Страницы: 4

Бренд: GBD Страницы: 68

Бренд: Rane Страницы: 2

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Klimaire Страницы: 5

Бренд: Kampmann Страницы: 5

Бренд: Apex Toys Страницы: 7

Бренд: IR-Tec Страницы: 14

U-verse Advance Series A10

Бренд: AT&T Страницы: 2

Бренд: Goodson Страницы: 4

Бренд: Moeller Страницы: 2

Бренд: Heat & Cool Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды