Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 191 | Manualshive

Страница: 191 / 330

background image

4 TROUBLESHOOTING

4.4 Troubleshooting by Symptom

189

4

Transient transmission failed

The following lists the actions to be taken if transient transmission cannot be performed with the target station, and the
engineering tool cannot perform monitoring.

Check item

Action

Is the D LINK LED of the RJ71GN11-T2 turned off?

If turned off, perform troubleshooting for when the D LINK LED
turns off or is flashing. (



Page 163 When the D LINK LED

turns off or is flashing)

Is the data link status of the target station normal?

In the CC-Link IE TSN/CC-Link IE Field diagnostics, identify the
cause of the error and take action. (



Page 169 Checking the

Network Status)

Is the following control data of the module FB or dedicated instruction correct?

• CPU type of the target module
• Target network number
• Target station number
• Target IP address

Correct the control data of the module FB or dedicated
instruction.

Is the network number overlapped on the network?

Change the overlapped network number.

Are multiple link dedicated instructions with the same channel setting executed
simultaneously?

• Set a different channel to each instruction.
• Shift the execution timing of the link dedicated instructions.

Is "







" displayed on the dot matrix LED of the RJ71GN11-T2?

• Set the module parameters.
• Check the firmware version of the RJ71GN11-T2. When

module parameters that are not supported are set, upgrade the
firmware version or correct the module parameters.

When "Connection Device
Information" under "Basic
Settings" of the master station
is set to "CC-Link IE TSN Class
B Only"

Are CC-Link IE TSN Class A devices connected?

• Check the connected device and disconnect the CC-Link IE

TSN Class A devices.

• When connecting a CC-Link IE TSN Class A device, set

"Connection Device Information" of the master station to
"Mixture of CC-Link IE TSN Class B/A or CC-Link IE TSN
Class A Only".

Is a general-purpose hub connected between CC-Link
IE TSN Class B devices?

Check the connected device and disconnect the general-purpose
hub or replace it with a TSN hub.

«
...
189
190
191
192
193
...
»

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R CC-Link IE TSN

Бренд: Jafar Страницы: 9

Бренд: Baby Jogger Страницы: 16

Бренд: Eaton Страницы: 100

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Бренд: Elby Designs Страницы: 4

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: K&K Страницы: 6

WisLink LPWAN RAK5146

Бренд: RAKwireless Страницы: 9

CURTIS DC Series

Бренд: NOCO Genius Страницы: 2

Бренд: TimeTec Security Страницы: 2

Бренд: Xylem Страницы: 2

Бренд: Ezodo Страницы: 7

Бренд: NXP Semiconductors Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды