manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 73

1  FUNCTIONS

1.5  RAS

71

1

Program that detects loopback station numbers (master operating station only)

By detecting loopback station numbers, a faulty station can be found. Whether loopback is being performed or not can be 
checked using 'Network topology setting' (SB0078) and 'Loopback status' (SB0065) of the master operating station.

Ex.

Program that stores loopback station numbers to 'wLoopbackStationNumber_1' (D1000) and 'wLoopbackStationNumber_2' 
(D1001)

Precautions

■

Supported version

To use the loopback function, check that all stations support ring topology. (

 Page 320 Added and Enhanced Functions)

■

Loopback function setting and network configuration

To use the loopback function, configure the network in ring topology and set "Network Topology" to "Ring" in "Basic Settings" 
of the master station. If "Network Topology" and the network configuration are inconsistent, an error may occur in all stations 
and data link cannot be performed.

■

When a loopback occurs or a loopback is resolved

Due to the occurrence or resolution of a loopback, transient transmission may become temporarily impossible. The following 
shows the periods of time until transient transmission becomes possible again.
 • A period of time until transient transmission becomes possible after the occurrence of a loopback: Maximum 1.1 seconds
 • A period of time until transient transmission becomes possible after the resolution of a loopback: Maximum 1.3 seconds
Transient transmission executed at the time of the occurrence or resolution of a loopback may be completed with an error. In 
such a case, execute transient transmission again. For a dedicated instruction, set transient transmission so that it will not be 
completed with an error by increasing the number of resends or extending the monitoring time.

Classification

Label name

Description

Device

Module label

GN11_1.bSts_DataLinkError

Data link error status of own station

SB0049

GN11_1.bOpe_Loopback

Loopback status

SB0065

GN11_1.bSet_RingTopology

Network topology setting

SB0078

GN11_1.wnVal_LoopbackStationNumber[1]

Loopback station number 1

SW0070

GN11_1.wnVal_LoopbackStationNumber[2]

Loopback station number 2

SW0071

Label to be defined

Define global labels as shown below:

(3) When 'Network topology setting' (SB0078) and 'Loopback status' (SB0065) are on, 'Loopback station number 1' (SW0070) and 'Loopback station number 2' 

(SW0071) are saved.

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды