manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 322

320

APPX
Appendix 10  Added and Enhanced Functions

Appendix 10

Added and Enhanced Functions

The following table lists the added and enhanced functions in the RJ71GN11-T2.

*1 For details on firmware update, refer to the following.

 MELSEC iQ-R Module Configuration Manual

*2 There are restrictions on the CPU module to be used. For details, refer to the following.

 MELSEC iQ-R CPU Module User's Manual (Application)

Added and enhanced functions

Firmware version

Updated the firmware using the engineering tool

*1

"01" or later

Multicast function to the communication mode under the application settings

"04" or later

Communication speed of 100Mbps

"04" or later

TSN hub

"05" or later

CC-Link IE TSN network synchronous communication function

*2

"10" or later

Safety communications in a system using the Safety CPU

*2

"10" or later

Station information list

"10" or later

Loopback function

"10" or later

Remote device test

"10" or later

Ring topology

"10" or later

CANopen communications

"11" or later

Watchdog counter

"11" or later

Increase in the number of inter-module synchronization target modules

"11" or later

CC-Link IE TSN Communication Software

"12" or later

Restriction cancellation on CC-Link IE TSN Class A devices/Ethernet devices in multicast mode

"14" or later

Compatible with time-managed polling (protocol version 2.0)

"14" or later

Improvement of detection of connected/disconnected devices function

"15" or later

Connection with a CC-Link IE TSN Class A device that supports the CANopen profile with the protocol 
version 2.0

"15" or later

Co-recording

"17" or later

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды