manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 199

4  TROUBLESHOOTING

4.4  Troubleshooting by Symptom

197

4

The control CPU of the local station cannot be synchronized time

When the time synchronization does not operate for the control CPU of a local station, check the following items.

Check item

Action

Is the daylight savings time set to CPU modules different between the 
master station and local stations?

Set the same daylight savings time to the CPU modules of the master station and 
local stations.

Has the clock data been changed by the clock function of the CPU 
module?

Check whether the clock data has been changed by the clock function of the CPU 
module.

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды