manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN Скачать руководство пользователя страница 71

1  FUNCTIONS

1.5  RAS

69

1

Loopback Function

This function continues data link with normal stations even if a cable disconnection or faulty station occurs in a ring topology 
network configuration. All stations after the cable disconnection point or faulty station are disconnected in a line topology. By 
using this function with ring topology, data link continues with normal stations.

Before using this function, check the firmware version of the RJ71GN11-T2. (

 Page 320 Added and 

Enhanced Functions)

Cable disconnection

■

Ring topology

Even if a cable disconnection occurs, the system automatically performs a loopback to continue the data link.

■

Line topology

Stations connected after the cable disconnection point are disconnected.

Occurrence of faulty stations

■

Ring topology

The system disconnects faulty stations and automatically performs a loopback to continue the data link.

■

Line topology

Stations connected after the faulty station are disconnected.

Disconnected

Disconnected

Fault

Fault

Содержание MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды