Mitsubishi Electric FR-F820-00046, Инструкция по эксплуатации

Страница: 459 / 940

Parameters (T) Multi-Function Input Terminal Parameters
FR-F800 5 - 287
When Pr. 59 "Remote function selection"
≠
"0", functions of the RL, RM, and RH signals will be
changed as in the table.
OH signal will operate with the relay contact "open".
Available when the plug-in option is connected. For details, refer to the Instruction Manual of the
option.
The setting is available only for standard models.
65 X65
PU/NET operation switchover
(PU operation with X65-ON)
Pr. 79, Pr. 340 5-119
66 X66
External/NET operation switchover
(NET operation with X66-ON)
Pr. 79, Pr. 340 5-119
67 X67
Command source switchover
(Command by Pr. 338, Pr. 339 enabled with X67-ON)
Pr. 338, Pr. 339 5-130
70 X70
DC feeding operation permission
Pr. 30 5-552
71 X71
DC feeding cancel
Pr. 30 5-552
72 X72 PID P control switchover
Pr. 127 to Pr. 134,
Pr. 575 to Pr. 577
5-353
73 X73 Second PID P control switchover
Pr. 127 to Pr. 134,
Pr. 575 to Pr. 577
5-353
77 X77 Pre-charge end command Pr. 760 to Pr. 764 5-385
78 X78 Second pre-charge end command Pr. 765 to Pr. 769 5-385
79 X79 Second PID forward/reverse action switchover Pr. 753 to Pr. 758 5-353
80 X80 Second PID control valid terminal Pr. 753 to Pr. 758 5-353
81 PGT PID gain tuning start/forced end Pr. 1211 to Pr. 1219 5-373
84 X84
Emergency drive execution command
Pr. 514, Pr. 515, Pr. 523, Pr. 524,
Pr. 1013
5-167
94 X94
Control signal input for main circuit power supply
MC
Pr. 30, Pr. 137, Pr. 248, Pr. 254 5-342
95 X95 Converter unit fault input
Pr. 57, Pr. 58, Pr. 135 to Pr. 139,
Pr. 159
5-333
96 X96 Converter unit fault input (E.OHT, E.CPU) input
97 X97 Cleaning valid
Pr. 1469 to Pr. 1479 5-348
98 X98 Cleaning trigger
9999
⎯
No function
⎯ ⎯
NOTES Same function can be assigned to two or more terminals. In this case, the logic of terminal input is
OR.
Priority of the speed command is JOG > multi-speed setting (RH, RM, RL, REX) > PID (X14).
When the (X10) signal is not set up, Pr. 79 "Operation mode selection" = "7", and PU operation
external interlock (X12) signal is Inverter run enable signal.
Same signal is used to assign multi-speed (7 speed) and remote setting. Setting cannot be per-
formed individually.
When the terminal assignment is changed using Pr. 178 to Pr. 189 (input terminal function selec-
tion), the terminal name will be different, which may result in an error of wiring, or affect other
functions. Set parameters after confirming the function of each terminal.
Setting
Signal
name
Function Related parameter
Refer to
page
Tab. 5-126: Input terminal function assignment (2)