MIPS MIPS32 74K Series Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 156

background image

CP0 register summary and reference

149

Programming the MIPS32® 74K™ Core Family, Revision 02.14

TagLo-WST[L,LP]

: cache-line locking control bits, held in the way select RAM, and parity over them.

TagLo-WST[LRU]

: When you read or write the tag in way select test mode (that is, with

ErrCtl[WST]

set) this field

reads or writes the LRU ("least recently used") state bits, held in the way select RAM.

The dirty RAM is another slice of the cache memory (distinct from the tag and data arrays). Test software can access
either by

cache

load-tag/store-tag operations when

ErrCtl[DYT]

is set: then you get the data in these fields. For

experts only.

Figure B.4 Fields in the TagLo-DAT Register

TagLo-DAT[D,DP]

: cache line "dirty" bits (and parity across them).

TagLo-DAT[A]

: cache line "alias" bits.

B.3.2 Dual (virtual and physical) tags in the 74K core D-cache — DTagHi register

In the 74K core the D-cache tags contain more information which is held in the

DTagHi

register. Regular software

probably need never touch it, and it’s mostly for diagnostic and test use.

Figure B.5 Fields in the DTagHi Register

DTagHi[ASID,G,VTAG]

: 74K family cores have a dual-tagged D-cache, combining a virtual tag for fast lookup with a

physical tag for correctness. The virtual tag provides a very fast way of predicting whether there’s a cache hit, and if
so which "way" of the cache will contain the right data. But the virtual tag check is heuristic: in some cases it will
turn out, once the physical address is available and can be checked against the physical tag, that we got it wrong.

From a software viewpoint the D-cache looks just like the “standard” MIPS virtually-indexed physically-tagged
cache, though there is occasionally an unexpected delay when the virtual tag “prediction” is wrong — the CPU pipe-
line treats this like a cache miss, and as a side-effect the virtual tag is adjusted so it will work correctly next time.

So these fields store the information required to match a virtual address: the virtual address itself, the ASID (tracking
the “address space identifier” maintained in

EntryHi[ASID]

) and a global (“G”) bit which can be set to make it not

necessary to match the ASID.

B.3.3 Pre-decode information in the I-cache - the ITagHi Register

For diagnostics only:

Figure B.6 Fields in the ITagHi Register

ITagHi[PREC,P]

: 74K family cores do some decoding of instructions when they’re loaded into the I-cache, which

helps speed instruction dispatch. When you use

cache

tag load/store instructions, you see that information here.

31

24

23

20

19

16

15

12

11

10

9

8

7

6

1

0

U

DP

D

U

A

0

U

0

U

31

12

11

9

8

7

0

VTAG

0

G

ASID

31

25

24

18

17

11

10

4

3

2

1

0

PREC_67

PREC_45

PREC_23

PREC_01

P_67

P_45

P_23

P_01

«
...
147
148
149
150
151
...
»

Содержание MIPS32 74K Series





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MIPS32 74K Series

Бренд: Magnat Audio Страницы: 2

Бренд: NAIM Страницы: 2

Бренд: Jabra Страницы: 15

Бренд: Paradyne Страницы: 112

NetStructure ZT 5515

Бренд: Intel Страницы: 90

Бренд: Clavister Страницы: 89

Бренд: Measurement Computing Страницы: 27

Бренд: Hama Страницы: 6

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренд: WABCO Страницы: 29

Wireless Connectivity Cape

Бренд: Element14 Страницы: 2

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренд: Idis Страницы: 17

5200 Live Series EventCD

Бренд: MF DIGITAL Страницы: 21

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Slideaway CL1008

Бренд: ATEN Страницы: 77

IP-Logic ZIG-IPPRO-RX

Бренд: Zigen Страницы: 4

Бренд: Vecow Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды