MIPS MIPS32 74K Series Скачать руководство пользователя страница 108

Страница: 108 / 156

8.1 EJTAG on-chip debug unit

Programming the MIPS32® 74K™ Core Family, Revision 02.14

108

DDBSImpr

: imprecise store breakpoint - see

Section 8.1.13, "Imprecise debug breaks"

below.

DEPC

probably points to

an instruction some time later in sequence than the store which triggered the breakpoint. The debugger or user (or
both) have to cope as best they can.

DDBLImpr

: imprecise load breakpoint. (See note on imprecise store breakpoint, above).

DINT

: debug interrupt: either the

DINT

signal got asserted or the probe wrote

EJTAG_CONTROL[EjtagBrk]

through

the JTAG signals.

DIB

: instruction breakpoint. If

DBp

is clear, that must have been from an

sdbbp

DDBS

: precise store breakpoint.

DDBL

: precise load breakpoint.

DBp

: any sort of match with a hardware breakpoint.

DSS

: single-step exception.

These note exceptions caused by instructions run in debug mode, but which have not happened yet because they are
imprecise and

Debug[IEXI]

is set. They remain set until

Debug[IEXI]

is cleared explicitly or implicitly by a

deret

when the exception is delivered and the pending bit cleared:

IBusEP

: bus error on instruction fetch pending. This exception is precise on the 74K core, so this can’t happen and the

field is always zero.

MCheckP

: machine check pending (usually an illegal TLB update). As above, on the 74K core, so this is always zero.

CacheEP

: cache parity error pending.

DBusEP

: bus error on data access pending.

8.1.7 The DCR (debug control) memory-mapped register

This is a memory-mapped EJTAG register . It’s found in “drseg” at location 0xFF30.0000 as shown in

Table 8.2

(but

only accessible if the CPU is in debug mode). The fields are in

Figure 8.4

Figure 8.2 Exception cause bits in the debug register

Debug

DDBSImpr DDBLImpr

DINT DIB DDBS DDBL DBp DSS

Figure 8.3 Debug register - exception-pending flags

Debug

IBusEP MCheckP CacheEP DBusEP

Содержание MIPS32 74K Series





























































































































































Результаты поиска

Содержание MIPS32 74K Series

Отзывы:

Похожие инструкции для MIPS32 74K Series

Бренды по названию

Популярные бренды

MIPS MIPS32 74K Series, Руководство по программированию

Результаты поиска

Содержание MIPS32 74K Series

Отзывы:

Похожие инструкции для MIPS32 74K Series

Бренды по названию

Популярные бренды