MIPS MIPS32 74K Series Скачать руководство пользователя страница 124

Страница: 124 / 156

8.2 PDtrace™ instruction trace facility

Programming the MIPS32® 74K™ Core Family, Revision 02.14

124

: "trace all branch" - when 1, output all branch addresses in full. Normally, predictable branches need not be sent.

: "inhibit overflow" - slow the CPU rather than lose trace data because you can’t capture it fast enough.

D, E, K, S, U

: do trace in various CPU modes: separate bits independently filter for debug, exception, kernel, supervisor

and user mode. Set 1 to trace.

ASID_M, ASID, G

: controls ability to trace for just one (or some) processes, recognized by their current ASID value as

found in

EntryHi[ASID]

. Set the

("global") to trace instructions from all and any ASIDs. Otherwise set

TraceControl[ASID]

to the value you want to trace and

ASID_M

to all 1s (you can also use

ASID_M

as a bit mask to

select several ASID values at once).

TFCR

: switch on to generate full PC addresses for all function call and return instructions.

TLSM

: switch on to trace all D-cache misses (potentially including the miss address).

TIM

: switch on to trace all I-cache misses.

: master trace on/off switch - set 0 to do no tracing at all.

The read-only fields in

TraceControl2

provide information about the capabilities of your PDtrace system. That system

may include a plug-in probe, and in that case the

TraceControl2[SyP]

field may read as garbage until the probe is

plugged in.

Mode

: whenever trace is turned on, you capture an instruction trace.

Mode

is a bit mask which determines what load/

store tracing will be done

. It’s coded like this:

However, see

TraceControl2[ValidModes]

(description below) for what your PDtrace unit is actually capable of doing.

Bad things can happen if you request a trace mode which isn’t available.

TraceControl2[ValidModes]

: what is this PDtrace unit capable of tracing?

Bit No Set What gets traced

Load addresses

Store addresses

Load data

Store data

31. Prior to v4 of the PDtrace specification, this field was in

TraceControl

, and was too small to allow all conditions to be speci-

fied independently.

ValidModes

What can we trace?

PC trace only

Can trace load/store addresses

Can trace load/store addresses and data

Содержание MIPS32 74K Series





























































































































































Результаты поиска

Содержание MIPS32 74K Series

Отзывы:

MIPS MIPS32 74K Series, Руководство по программированию, Страница: 124 / 156

Результаты поиска

Содержание MIPS32 74K Series

Отзывы: