MIMAKI Textile Jet Tx3-1600 Скачать руководство пользователя

Страница: 33 / 218

- 1.13 -

Fabric retainer

If the edge of the fabric is curled or it is raised, it may be caught by the head or inferior ink dis-

charge may occur. To avoid this trouble, use the fabric pressers. (Refer to Page1.12)

• The fabric retainer slide part also act as a detection board which detects

the printing width.

Printing with the full width (up to 1620mm width) is possible by setting the

fabric retainer to a position apart from the edge. (1620mm width or less )

• The fabric retainer is detachable for washing in case it’s stained by ink.

Remove the hand screw and then remove the fabric retainer.

• When using fabric retainer, be sure to adjust the head height to 3mm or

more. Using them with a low head height may cause damage.

Hand screw

Fabric retainer

Slide part

Содержание Textile Jet Tx3-1600



























































































































































































































Результаты поиска

Содержание Textile Jet Tx3-1600

Отзывы:

Похожие инструкции для Textile Jet Tx3-1600

Бренды по названию

Популярные бренды

MIMAKI Textile Jet Tx3-1600, Руководство по эксплуатации

Результаты поиска

Содержание Textile Jet Tx3-1600

Отзывы:

Похожие инструкции для Textile Jet Tx3-1600

Бренды по названию

Популярные бренды