MIMAKI Textile Jet Tx3-1600 Скачать руководство пользователя страница 200

Страница: 200 / 218

- 6.8 -

Something wrong with the peeling
system.

Flushing box has not been set.

Time to clean the flushing box.

Temperature is below operable
condition 5 degree or more.

Time to replace the battery.

Water in the wash tank is below
level.

Time to replace the washing filter.

Check the position of fabric.

1. If the fabric is peeled off up to

the head position

• Set the position of the

pressure roller to HIGH.

• Lower the printing rate and

perform re-printing.

• Adhesive has been

degraded. Reapply adhesive.

2. If the fabric is transported

adhering to the belt, move the
pressure roller position to LOW.

3. In case the same error message

appears again on the LCD,
contact your local distributor to
call for service.

Attach the running flushing box.

Cleaning the running flushing box
or draining the waste ink. In case
the filter has been dirt, clean it .
(Refer to Page 3.24)

Adjust the temperature of the
peripheral environment to
appropriate temperature.

Contact your dealer or Mimaki
sales office.

Add water to the cleaning liquid
tank.

Change the cleaning water filter
with a new one. Then, execute
Maintenance Function-Counter
Reset to reset the counter of the
cleaning filter.
(Refer to Page 3.4, 5.20)

Peeling Error

Press [ ENT ] Key

Warning message

Cause

Corrective measure

Flushing Box

No Flushing Box

Flushing Box

Empty The Ink

Blower Operable

Temperature

REPLACE BATTERY

Wash Tank

Check The Water

Wash Tank

Check The Filter

Peeling Error

Check The Media

Wash Tank

Press [ ENT ] Key

Wash Tank

Check The Water

Local mode

Содержание Textile Jet Tx3-1600



























































































































































































































Результаты поиска

Содержание Textile Jet Tx3-1600

Отзывы:

Похожие инструкции для Textile Jet Tx3-1600

Бренды по названию

Популярные бренды

MIMAKI Textile Jet Tx3-1600, Руководство по эксплуатации

Результаты поиска

Содержание Textile Jet Tx3-1600

Отзывы:

Похожие инструкции для Textile Jet Tx3-1600

Бренды по названию

Популярные бренды