MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 58

Страница: 58 / 146

Section 3 - On The Water

Page 50

90-864839061 NOVEMBER 2006

Operation Chart

BEFORE STARTING

AFTER STARTING

WHILE UNDERWAY

AFTER STOPPING

Listen for Audio Warning

Alarm to sound when the

ignition switch is in the

"ON" position.

Starting and Stopping the Engine

NOTE: Perform only those functions applicable to your power package.

STARTING THE ENGINE

1. Check all items listed in the Operation Chart.
2. Place the remote control handle in neutral.

CAUTION

Overheating from insufficient cooling water will cause engine and drive system damage.

Ensure that there is sufficient water always available at water inlet holes during operation.

WARNING

Avoid fire or explosion. Before starting the engine, operate the bilge blower for at least

five minutes to remove any explosive fumes from the engine compartment. If the boat is

not equipped with a bilge blower, open the engine hatch and leave it open while starting

the engine.

NOTE: MerCruiser DTS models are equipped with SmartStart. The SmartStart feature

incorporates push button starting. Rather than holding the start button or key switch to start

the engine and then releasing it when the engine starts, SmartStart completely controls

the starting process. When the start button is pushed, the DTS system signals the engine

PCM to start the engine. If the engine does not start, the starting process times out after

eight seconds or when the engine reaches 400 RPM. Attempting to start the engine with

the engine already running will turn the engine off.

3. Turn ignition key to "RUN" position.
4. Turn the ignition key switch to the "START" position then release, or depress the start/

stop button and release. If the engine is cold, allow the engine to operate at idle for

6‑10 minutes or until the engine temperature reaches 60 °C (140 °F).

5. If the engine does not start after three attempts:

Push the throttle‑only button and position the remote control handle or throttle

lever to the 1/4 throttle position.

Turn the ignition key to "start." Release key when the engine starts and allow the

switch to return to the "on" position.

6. If the engine does not start after step 5:

Move the remote control handle.throttle lever to the full throttle position, then return

to 1/4 throttle.

Turn the ignition key to "start." Release key when the engine starts and allow the

switch to return to the "on" position.

7. Inspect the power package for fuel, oil, water, and exhaust leaks.
8. Move the control handle with a firm, quick motion forward to shift to forward gear, or

backward to shift to reverse. After shifting, advance throttle to desired setting.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды