MerCruiser 496 MAG Bravo Скачать руководство пользователя страница 110

Страница: 110 / 146

Section 5 - Maintenance

Page 102

90-864839061 NOVEMBER 2006

If the tensioner is contacting either of the limits during operation, check the mounting

brackets and the belt length. Loose brackets, bracket failure, accessory drive component

movement, incorrect belt length, or belt failure can cause the tensioner to contact the limits.
See your authorized MerCruiser dealer for service if these conditions exist.

CAUTION

The belt tensioner assembly contains a high tension spring. Rapid release of the

tensioner, or allowing the tensioner to snap back quickly, could injure the operator or

cause product damage. Relieve the spring tension slowly to avoid injury or product

damage.

1. Use a breaker bar and appropriate socket to hold back the tensioner and relieve the

belt tension. Rotate the tensioner away from belt until it stops. Remove the belt from

the idler pulley and slowly relieve the tension on the breaker bar.

8115

Breaker bar with arrow in direction of movement to relieve tension.

a -

Breaker bar

2. Remove the belt and reroute the replacement belt according to the belt routing diagram.

Содержание 496 MAG Bravo



















































































































































Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды

MerCruiser 496 MAG Bravo, Руководство пользователя

Результаты поиска

Содержание 496 MAG Bravo

Отзывы:

Похожие инструкции для 496 MAG Bravo

Бренды по названию

Популярные бренды